---
title: "SF Series Solid Linear Shaft: Metric 3–150 mm, HRC 60–62"
date: 2026-11-18
description: "Product OverviewThe SF series is the metric solid shaft of the MS Linear shaft range, ground from GCr15 bearing steel and hardened to HRC 60–62. It is the shaft..."
source: https://www.mslinear.com/linear-shaft/sf-series-solid-linear-shaft/
---

# SF Series Solid Linear Shaft: Metric 3–150 mm, HRC 60–62

## Product Overview

The SF series is the metric solid shaft of the MS Linear shaft range, ground from GCr15 bearing steel and hardened to HRC 60–62. It is the shaft an engineer reaches for when the axis is a plain linear bearing, a clamp, a pivot or a support along which a carriage runs.

Diameters run from 3 mm to 150 mm and single-piece lengths to 6000 mm; longer runs are supplied as butted lengths with a dowel or threaded joint, machined so the joint does not stand proud of the running surface. Ends can be threaded, stepped, keyed, drilled or tapped, and the finished part can carry hard chrome.

The running surface is supplied in h6 or g6, so the shaft can be matched to the housing bore of an adjustable or fixed linear bearing. It is not a drop-in substitute for a profile rail: the shaft carries point loads through a sleeve, so support spacing and deflection have to be checked, which is covered in the [shaft selection guide](/linear-shaft-selection/).

<table class="ms-spec-table"><tr><th>Parameter</th><th>Specification</th></tr><tr><td>Series</td><td>SF solid linear shaft, metric</td></tr><tr><td>Diameter range</td><td>3 mm to 150 mm, ground in steps</td></tr><tr><td>Material</td><td>GCr15 bearing steel (SUJ2)</td></tr><tr><td>Hardness</td><td>HRC 60–62 through the case</td></tr><tr><td>Case depth</td><td>0.4–0.7 mm below 6 mm; 0.6–1.5 mm 10–15 mm; 0.8–2.0 mm 16–20 mm; 0.8–3.0 mm above 25 mm</td></tr><tr><td>Tolerance</td><td>h6 or g6, per size table</td></tr><tr><td>Maximum length</td><td>6000 mm in one piece; longer by butted joint</td></tr><tr><td>Straightness</td><td>Per length class, checked on the bench</td></tr><tr><td>Surface</td><td>Ground; hard chrome optional</td></tr><tr><td>End machining</td><td>Thread, step, keyway, radial holes, coaxial bores</td></tr><tr><td>Minimum order</td><td>1 piece</td></tr><tr><td>Lead time</td><td>3–7 days standard; 10–15 days with end machining</td></tr></table>

## Product Features

- Case-hardened surface with a soft core, so the shaft resists wear without becoming brittle at the ends.
- h6 and g6 stock tolerances match the bore of adjustable SDM and LM bearings and remove the need to ream a housing.
- Straightness is checked over the full length, not sampled at the ends, because a bowed shaft shows up as a tight spot mid-stroke.
- End machining is done after hardening and before final grinding, so the thread and the running surface stay concentric.
- Butted joints use a dowel or a threaded stud with a ground face, keeping the seam out of the loaded zone.
- Hard chrome and stainless grades are available for wash-down and humid cells.

## Applications

Shaft axes suit medium loads over moderate strokes where a sleeve is cheaper than a profile rail. For heavy side loads or a cantilever, compare with the [round shaft and profile rail comparison](/cylindrical-guide-vs-square-guide/) before fixing the layout.

## About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.
