KBE Open-Type Cylindrical Guide: 16–50 mm, Supported Shaft

KBE Open-Type Cylindrical Guide: 16–50 mm, Supported Shaft
+

Key Features

Open block for a shaft supported along its length, with the open mouth sealed as well as the ends.

16–50 mmShaft diameter
2,160 NMax dynamic
Open typeSupported shaft

Applications

Long travel axes Supported shafts Cutting bridges Conveyor gates Test stands

Cylindrical Guides · KBE Open-Type Cylindrical Guide: 16–50 mm, Supported Shaft

Technical Description and Selection Reference

Product Overview

The KBE series is an open-type cylindrical guide: the carriage wraps a shaft that is supported along its length, with an opening on one side so the shaft can pass a support rail or a bracket. It is used where the shaft cannot be free-standing, typically on a long axis with intermediate supports.

Sizes run from 16 mm to 50 mm shafts. The open mouth is set at an angle, and the block is built so the load still passes through the ball or plain contact rather than through the opening. Seals cover the open side as well as the ends.

The trade-off is stiffness: an open block carries less moment than a closed one of the same size, and the support spacing becomes the real limit on accuracy. The round shaft comparison sets out when an open block is still worth it and when a profile rail wins.

ParameterSpecification
SeriesKBE open-type cylindrical guide
Shaft diameter16, 20, 25, 30, 40, 50 mm
CarriageAluminium, open mouth, sealed
Dynamic load (reference)About 774 N at KBE16 to about 2,160 N at KBE40
Static load (reference)About 1,180 N at KBE16 to about 4,020 N at KBE40
Contact angleSet by the open geometry, quoted per size
Mounting boltsM5 to M10, per size
Shaft toleranceh6 or g6
SupportShaft supported along its length; spacing from deflection
StrokeSet by shaft and support layout
Minimum order1 piece
Lead time7–10 days; 10–15 days custom

Product Features

  • Open mouth lets the shaft pass a support rail, so a long axis can be built from supported sections.
  • Seals cover the open side as well as the ends, which is where an open block usually leaks dust.
  • Load path stays through the contact, not through the opening.
  • Aluminium carriage keeps mass low on a long, fast axis.
  • Supported shaft converts a deflection problem into a support-spacing decision.

Applications

Long stroke on a modest budget: support the shaft at intervals and the open block tracks it without a profile rail.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

A round shaft axis is the lower-cost choice for short stroke, moderate load and a simple frame. A profile rail wins once the carriage sees a real moment, the stroke is long, or the accuracy has to hold under side load. The comparison page on this site sets out the crossover.

SC is a single shaft with an aluminium carriage, the simplest and cheapest axis. SBR and TBR put two shafts in one block, which resists roll without a second rail to align. KBE is an open block for a shaft that is supported along its length, used where the shaft has to pass a support rail.

The long carriage spreads the load over more shaft and takes more moment, which is the usual fix when a short block rocks at the end of the stroke. If the load is centred and the stroke is short, the standard body is enough. Tell us the overhang and the load position and we will size the body.

Yes. The standard build uses UU double seals, and PP seals are available on the twin-rail family. For fine dust or coolant mist, add a bellows cover: a seal keeps chips out of the bore but it does not stop a build-up on the shaft.

Yes. Cylindrical Guides is supplied as a matched set on request, with the shaft lengths cut to your stroke and the end supports drilled to the same centre distance. That removes the alignment step on the machine frame.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Cylindrical Guides from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts