Technical guide

How to select a linear guideway

Most wrong rails are chosen the same way: a size is picked from a catalogue page that looks about right, and the load case is checked afterwards. These six steps put the numbers in order first, so the size you land on has a reason.

Six steps 18 guideway series Worked load example Accuracy and preload tables
01Load case

Five numbers before you open a catalogue

A guideway is sized by the load it carries, not by the machine it sits in. Write these down first; if one of them is missing, that is the part to settle before anything else.

1Load per carriage, including the moment from an offset centre of gravity
2Stroke length and the number of carriages per rail
3Maximum speed and acceleration, or the cycle time if that is what you know
4Required accuracy or repeatability over the full stroke
5Environment: chips, coolant, dust, cleanroom, vacuum, ambient temperature
+Target service life in kilometres or years, whichever your customer asks for

Two of these decide the family on their own: the direction the load acts from, and whether the structure needs stiffness or speed. The rest decide the size and the grade.

02Family

Pick the family from the load case

Ball and roller rails are not interchangeable grades of the same product. They differ in what they do under load, and the family choice fixes the envelope before a size is even discussed.

Load caseFamilyWhy it fits
General machining, load from four directionsHGFour-row ball, equal capacity in all directions, self-aligning on a slightly uneven bed.
Compact automation, low profile, high speedEG · QELow height keeps the moving mass down; QE adds the silent ball return for noise-sensitive lines.
Heavy cutting, high rigidity on a ball railQHSame envelope as a standard ball rail but more balls in contact and a stiffer block.
Single rail carrying an overhanging loadQW · WEWide rail resists roll moment that would twist a narrow block.
Heavy load, shock, interrupted cutRG · QR · URRoller contact spreads the load over more area: higher rigidity, more shock capacity, more friction.
Precision positioning, minimal frictionPG · AGTight height and parallelism control; used under measuring and wafer stages.
Chips, dust, weld splashCRG · SECovered raceway or metal end caps keep debris out where wipers alone are not enough.
Long intervals between serviceE2 · ELLubricant reservoir in the block carries the rail through long maintenance intervals.
Small strokes, light load, tight spaceMGMiniature rail for lab equipment, 3D printers and small pick-and-place heads.
Wet or corrosive environmentStainlessStainless rail and block where washdown or Chemicals rule out coated carbon steel.
High temperature or anti-torqueCGAnti-torque block where a single rail must not rotate under an offset load.

If two families both look plausible, the deciding question is usually stiffness against speed. A roller rail that is stiff enough for the cut will be slower and noisier than the ball rail the application actually needed. The two contact types, their rating bases and the cases where each one wins are compared in ball vs roller guideway, and all the families are mapped by load, height, width and protection in the series comparison.

03Sizing

Size the rail from C, not from the picture

Every rail size has two ratings: C, the dynamic load rating the bearing survives for a nominal distance, and C0, the static rating before the raceway takes permanent deformation. They answer different questions.

L10 = (C / P)3 × 50 km   ball guideway
L10 = (C / P)10/3 × 100 km   roller guideway
Lh = L × 1000 / (60 × v)
P is the load on the most heavily loaded carriage, v the mean speed in m/min. Use the mean load when the cycle varies; a single worst-case figure overstates wear.

Alongside the life figure, check the static safety factor s0 = C0 / P0. Quiet machines run at 1.5 to 2, general machinery at 2 to 3, and anything with shock, press or drop loading at 3 to 5. A rail that passes the life calculation but sits at s0 = 1.2 will brinell the raceway on the first hard stop. When the load is offset from the block line, the moment is checked separately against M0; the method is in moment load on a guideway. The life figure also assumes the raceway keeps its grease film, so the relubrication interval belongs in the same calculation sheet, and it assumes a hard raceway running cool with no shocks, which is what the three correction factors put back.

Worked example 900 kg gantry, four carriages
Moving mass900 kg ≈ 8.8 kN
Load per carriage, static2.2 kN
Acceleration 1.0 m/s in 0.3 s≈ 3.3 m/s², inertia adds ~3.0 kN to the leading pair
Worst carriage with momentP ≈ 3.5 kN
Target life2,000 km
Required C3.5 × (2000 / 50)1/3 = 3.5 × 3.42 ≈ 12 kN
Read the size chart down to the first size whose C exceeds 12 kN — for the HG family that is usually the 25 class. Check C0 against the 3.5 kN with the shock factor before confirming: if the load sits far from the rail centre, the moment pushes the next size up.

If you would rather not do the arithmetic by hand, the size calculator takes the same inputs and returns the required C, the static check and a size.

Do not average the peak away

Use the mean load for life, the peak for static safety. They are two separate checks on the same drawing.

Watch the moment

An offset centre of gravity can double the load on one carriage. It is the most common reason a nominally correct size fails in service.

Leave room to grow

If the duty cycle is still being defined, size for the next step up rather than the current prototype.

04Accuracy

Accuracy grade decides what the machine can hold

The grade sets two things: the height tolerance between blocks, and the running parallelism of the carriage over the rail length. Both are assembly-level numbers, so a high grade on an unprepared bed buys nothing.

GradeWhat it buysTypical use
CStandard height tolerance and parallelismGeneral automation, packaging, transfer lines
HTighter height and parallelism than CMachine tools, routers, laser cutting
PPrecision grade, controlled over the full strokeCNC machining centres, measuring equipment
SPSuper precision, matched pairs availablePrecision measuring, semiconductor stages
UPUltra precision, the top of the rangeWafer inspection, ultra-precision machine tools
Where the money goes. Moving from C to H is a small step in price and a large step in what the machine can hold. Moving from P to SP doubles the cost and only pays off if the mounting surfaces are machined to match; otherwise the rail is accurate and the machine is not.
05Preload

Preload is a stiffness decision

Preload removes internal clearance between the balls or rollers and the raceway. It raises rigidity and repeatability, and it raises friction and heat at the same time. The right value is the one the application can cool. The grade and preload reference goes deeper on how the two choices interact.

CodeConditionUse when
Z0ClearanceLow friction matters more than stiffness; transport axes, light handling
Z1Light preloadGeneral motion with moderate external load, most automation
Z2Medium preloadCutting forces, vibration, reversing load, higher repeatability

Above Z2 the heat generated in the block becomes the limiting factor, not the load rating. If the axis runs continuously at high speed, medium preload with oil lubrication is usually a better answer than heavy preload with grease.

06Length

Rail length follows the stroke, not the bed

A rail has to carry the carriage through the whole stroke and keep it supported at both ends. The starting formula for one carriage is:

L = S + Lb + 2 × M
S is the stroke, Lb the block length, M the end margin. Keep M at roughly half a block length or more, and add the carriage spacing when two blocks share a rail.

Rails are normally supplied up to about 4 m. Beyond that the rail is jointed: sections are matched in height, the joint is placed outside the loaded zone, and the carriage should never cross a joint under full load if it can be avoided. Long travel is a drawing question, not a catalogue question — send the stroke and we lay out the joints. The placement and stagger rules are in joining two guideway rails.

Mounting surfaces matter as much as the rail grade. Parallelism between the two rails, and flatness along the bed, set the real accuracy of the axis. A P-grade rail bolted to a milled-but-unchecked surface behaves like a C-grade rail with a bind in the middle of the stroke. The figures and the measuring method are in mounting surface flatness, the assembly sequence in guideway installation, and the difference between a flat bed and a wall or inverted head in mounting orientation.

07Environment

Lubrication and protection, chosen for the room

Grease is the default: lithium soap, NLGI 2, applied to the block and wiped along the raceway on assembly. Re-grease by distance rather than by calendar — roughly every 100 km of travel in clean conditions, shorter where chips or coolant reach the rail. The conversion to hours, the fill procedure and the symptoms of a dry raceway are in guideway lubrication.

Oil suits high speed and continuous duty, where the block would otherwise run hot. Cleanrooms and vacuum need a low-outgassing grease, and the wipers have to be selected for the same reason: standard nitrile wipers outgas and the wrong grease condenses on the wafer.

Protection is a separate decision from lubrication. Bellows and way covers handle large chips; metal end caps handle hot chips and weld splash; a covered roller rail handles fine dust that would otherwise lap into the raceway. The sealing codes and when each one is enough are set out in dust protection.

08Inquiry

What to send with the inquiry

A drawing or a model code is enough to quote, but the load case is what lets us confirm the size instead of repeating what you asked for.

  • Rail length, stroke and the number of carriages per rail
  • Load per carriage, or the moving mass and its centre of gravity
  • Speed and acceleration, or the cycle time
  • Accuracy grade and preload, if already fixed by the design
  • Environment and lubrication requirement
  • Quantity for the first order and the expected annual volume
Send the load case

We reply with the size, grade and preload that fit it, plus the datasheet for that model.

Request a quotation Check stock sizes
09Questions

Questions that come with the drawing

Do I need to calculate life, or can I size by load alone?
Sizing by load alone is how undersized rails get specified. A rail that carries the load but runs out of fatigue life at twelve months is still the wrong rail. Check the static safety factor for shock and the L10 distance for the duty cycle; both take one line of arithmetic.
Can I replace a rail on an existing machine without changing the carriage?
Yes, when the mounting hole pattern, rail height and block envelope match the original. Send the original model code or a drawing with hole pitch and height; we machine to that pattern rather than to a nominal size.
When is a roller guideway worth the extra cost over a ball guideway?
When the load is heavy relative to the rail size, when shock or interrupted cutting is present, or when the structure needs stiffness rather than speed. Ball rails stay the better choice for high speed, low noise and low friction.
How long can one rail be before it has to be jointed?
Rails are normally supplied up to about 4 m; longer travel is built from jointed sections with the joint positioned away from the loaded zone and the sections matched in height. Tell us the stroke and we lay out the joint positions.
What accuracy grade does a CNC router need?
H grade covers most routers and general machine tools. Step to P where the finished part tolerance is tight over the full stroke, and to SP only when the machine is built around that grade: mounting surface parallelism has to match it.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts