01Two ranges, one question
Both families are ball guideways with four rows of balls and the same accuracy and preload language. They are not alternatives in the usual sense, where one is cheaper and one is better. They occupy different height bands, and the band decides which drawings are possible.
| Family | Carriage height H | Sizes in the catalogue | Rail length | Carriage styles |
|---|---|---|---|---|
| DG | 24 to 42 mm | 15, 20, 25, 30 | 100 to 4000 mm | Square section and wide section, short and long |
| TGH / TGL | 24 to 80 mm | 15 to 55 | Standard and joined rails | CA and HA on a shared rail |
The overlap is narrow: TGL at 24 and 28 mm sits in the same band as DG at the bottom of its range. Above 42 mm, DG stops and TG continues. Below 24 mm, the miniature family takes over. Sizing usually goes: measure the envelope, pick the band, then check load inside the band.
02What DG is built for
DG is a low-section family. The rail is wide relative to its height, the carriage is short in the vertical direction, and the fixing bolts go through the rail from the top with a second option from below. The point of that shape is stability against roll on a low, wide base, not maximum load in a tall stack.
The catalogue lists the carriage types as square and wide section, each in a short and a long version. The wide version is what makes a single rail behave like a small gantry: the extra width resists roll without adding height, which is the same argument the wide-rail family uses at larger sizes.
Rail length starts at 100 mm. That matters for compact machines: a short stroke on a short rail, with the block never overhanging the ends, is a configuration this family is designed to serve.
03What TG adds above 42 mm
Above the DG band, the TG family continues in the same structural language but with taller sections and larger ball rows. TGH and TGL share a rail and differ in carriage height; both are available from 15 up to 55, and TGW covers the wide-rail case at the same sizes.
The practical consequence is that a machine which outgrows DG does not have to change supplier language, accuracy grades or sealing conventions. It changes size and height, and the mounting hole pattern changes with it, which is the point where the base plate drawing is revisited.
If the requirement is load at a height above 42 mm, the TG tables carry it. If the requirement is a low stack at a load above what DG offers at 30, the honest options are a wider DG carriage, a second rail, or a re-think of the axis geometry, not a taller block squeezed into the same envelope.
04The matched-set consequence
DG accuracy in the catalogue is specified as a matched carriage and rail set, in the same way the preload and the running clearance are set at assembly. That has a procurement consequence worth knowing before the first order: a replacement carriage is ordered against the rail it will run on, not pulled off a shelf.
For a machine builder running a series, this is normal practice and adds nothing. For a maintenance department holding spares, it means the spare is a pair, and the pair carries the accuracy grade of the original. Plan the spare stock accordingly; a carriage ordered without the rail reference cannot be guaranteed to the same clearance.
TG, by contrast, is normally handled as interchangeable parts within a size and preload class, which is why mixed replacement is common there.
05Load and moment, read from the table
Ratings for DG are printed per size and per carriage style, and they differ between the short and the long carriage in the same way they do in TG. Two habits keep the selection honest:
- Use the block, not the family, as the unit. C and C0 belong to a specific carriage on a specific rail size. A family name does not carry a rating.
- Check the moment before the load. A low, wide carriage resists roll well but has a short vertical section, so pitch and yaw can run out earlier than expected on an overhanging load.
Both checks are arithmetic, not judgement: enter the load, the offsets and the block spacing in the load and life calculator, then compare the worst block against C and against M0 in the moment load page.
06Where this family is used
The applications printed against DG are automation equipment, high-speed transport, precision measuring instruments, semiconductor equipment and woodworking machinery. Read together, they describe a common envelope: a low, fast, moderately loaded axis inside a housing or under a table.
Woodworking and transport value speed and dirt tolerance more than stiffness. Measuring and semiconductor value flatness and repeatability more than load. A low section serves both, for different reasons, and that is why one family covers them.
Where the axis is a press, a machining centre or a heavy gantry, the load and moment put the requirement above this band, and the standard-height TG family is the correct next step.
07Lubrication and mounting differences
The oil supply rates printed for DG are small and size-specific: 0.1 cm³/hr at 15, 0.133 at 20, 0.167 at 25 and 0.2 at 30. Those figures are the reason a low-profile axis is usually grease-lubricated; an oil system sized for a large block will flood a small one. If oil is required by the process, meter it at the printed rate.
Mounting follows the same rules as any ball rail: a datum side, a tightening sequence and a check of the mounting surface flatness. The difference is the bolt access. DG rails can be fixed from the top or from below, and the choice is made at drawing stage because it decides whether the base plate needs through holes or tapped holes.
The installation sequence itself is the same as the rest of the family and is written out in installation sequence; the surface tolerance that has to be met first is in mounting surface.
08When to step up to TG
- The height budget opens up. Once 42 mm is no longer a constraint, the standard family offers more sizes and more rating per euro.
- Load or moment exceeds the DG table at 30. Do not stack two DG rails closer together to compensate unless the geometry genuinely supports it; a taller rail usually costs less than a re-designed base.
- Long joined rails. Above a few metres, the butt-joint rules and the rail section of the standard family are the better documented route.
- Spares strategy. If mixed replacement matters more than height, interchangeable parts simplify the stock.
09Where to go next
Inside the TG family, the height decision is covered in TGH against TGL, and the block length decision in CA against HA. If the axis is a single-rail gantry, wide rail guideways explains when width replaces a second rail.
For sizing across families, the series comparison maps every family by load, height, width and protection, and the size chart holds the ratings. All guideway families sit under linear guideways.
Send the envelope, the rail length and the load through the inquiry form and we confirm the band, the carriage style and whether the axis needs one rail or two.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
