Material

Stainless steel linear guideways: where they earn the price

Stainless is specified for the environment, not for the load. It solves corrosion, washdown and cleanroom problems that no coating fully solves, and it gives back a little capacity in return. The decision is easier once both sides are on the table.

9Cr18 / SUS440 HRC 55 5 min read

01Two steels, one difference that matters

MaterialHardnessWhat it means on an axis
GCr15 / SUJ2 bearing steelHRC 60–62The standard case. Highest rating, needs protection from moisture
9Cr18 / SUS440 stainlessHRC 55 and aboveCorrosion resistant, slightly lower hardness, ratings should be confirmed per size
Hard chrome on bearing steelCase dependentWear and rust protection on the raceway; not a substitute for stainless in washdown

The five-point hardness gap is not dramatic in itself, but life moves with the cube of the load ratio, and hardness enters the rating through a curve rather than a single number. Treat a stainless size as having slightly less margin than the alloy equivalent and check the actual rating in the catalogue instead of assuming they are identical.

02What stainless actually buys

  • Washdown and food handling. Detergents, steam and rinse water attack carbon steel at the raceway edges first. Stainless removes the rust allowance from the design and lets the machine be cleaned without re-greasing every surface.
  • Humidity and condensation. Cold rooms, unheated warehouses and machines that cycle between warm and cold air build condensate on the rail. A coated rail helps until the coating is scratched; stainless does not care.
  • Cleanroom and medical. No oiled carbon surface, no rust particles, and compatibility with cleaning agents.
  • Thin sections. Miniature rails cannot afford a corrosion allowance: the wall is a few millimetres. This is why the miniature families are stainless throughout, balls and retainers included.

03What stainless does not solve

Three limits are worth stating plainly, because they are the reason a stainless quotation can disappoint a buyer who expected a universal rail:

  • Chlorides. Salt water, brine and chlorine-based sanitisers pit 440 stainless. If the machine sees salt spray, specify the material and the surface treatment together, and test a coupon before the design is frozen.
  • Galvanic contact. Stainless against aluminium in a wet environment is a corrosion cell; use an insulating washer or a coated fastener at the joint.
  • Load. The rating is lower than the alloy equivalent, so the size that worked in carbon steel may need one step up in stainless. Recruit the life correction before comparing prices.

04Matching the rest of the axis

A stainless rail on a carbon-steel shaft is half a solution. The parts that touch the environment should share the material decision:

ComponentStainless optionNote
Guideway rail and block9Cr18 / SUS440, all metal partsBalls and retainers included on miniature sizes
Linear shaft9Cr18 / SUS440, HRC 55 and aboveHard chrome on GCr15 is the cheaper alternative for light washdown
Ball screwStainless screw with stainless nutCheck the preload class; stainless screws are often limited to lighter preload
FastenersA2 / A4 stainlessInsulate against aluminium to stop galvanic attack

The grease is the fourth component. In washdown duty it is removed faster than the 100 km rule predicts, so the interval follows the cleaning cycle; in cleanroom duty a low-outgassing grease matters more than the base oil viscosity.

05Cost, lead time and how to ask

Stainless costs more per kilogram and is usually produced in smaller batches, so the price premium is larger than the material difference. Two practical ways to keep it contained:

  • Use stainless only where the environment reaches: the rail and block inside the wash zone, standard material for the frame rails outside it.
  • Keep the size one step above the calculated minimum, because the stainless rating is lower and a second size step later is more expensive than the first.

On the RFQ, state the medium and the exposure, not just "stainless":

Medium washdown with alkaline detergent, daily
Exposure wet 20 min, then air dry; ambient 5–40 °C
Rail 15 size, 2 rails × 600 mm, 2 blocks each
Ask stainless grade, rating for that size, and the grease class

06Questions we get

Is stainless weaker than bearing steel?

Typically yes: about HRC 55 against HRC 60 to 62. The gap is small but real, so treat the stainless catalogue rating as a ceiling and confirm it for the size you pick.

Will 440 stainless resist salt water?

It resists fresh water, humidity and most detergents far better than carbon steel, but chlorides still pit the raceway. For salt spray, specify material and surface treatment together and test a sample first.

Does stainless need a different grease?

The metal does not change the lubricant requirement; the application does. Washdown uses food-grade grease on a cleaning-cycle interval, cleanroom uses low-outgassing grease, and neither follows the plain 100 km rule.

07Where to go next

All twenty guides, arranged by decision stage, are on the knowledge hub.

If the axis is small, read miniature selection first: the miniature families are stainless by construction. If the problem is chips rather than water, dust protection is the better lever. The rating arithmetic is on life correction, and the grease interval on relubrication.

Products: stainless steel guideway and MG miniature series. Send the cleaning agent and the exposure time and we will confirm the grade and the protection level.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts