Two shafts, one profile

Heavy-duty cylindrical guides: twin-shaft blocks and roller rails

A single shaft has little moment capacity. The usual answer is a second rail and a wider stance. The twin-shaft profile does that in one part: two hardened shafts pressed into one aluminium extrusion, with a carriage that wraps both.

SBR · TBR · SGR 6 m per length 5 min read

01Why the twin-shaft profile exists

Two separate shafts need two mounting faces, parallel in two planes, and the bearings cannot absorb the error. A profile with both shafts in one extrusion is one part with one mounting face, so the spacing and parallelism are set at the factory. The carriage wraps both shafts, which turns a pair of bearing lines into a block with a real moment base.

The cost is a fixed centre distance and a profile height; the benefit is assembly time and a predictable stance.

02The families

FamilyConstructionLoad path
SBRTwin shafts in an aluminium profile, ball carriageModerate load, smooth motion, long stroke
TBRHeavier twin-shaft profile, longer carriageHigher moment, gantry beams
SGR / SGBProfiled shaft with roller carriageHigh load and stiffness, quieter than ball at low speed
OSGShaft guide with side blocksWhere a side load acts on the carriage

The SGR family quotes a safe load and dynamic torques in two directions, which is the honest way to describe a roller guide: it is a moment device, not just a load device.

03Length, joints and the 6 m line

The catalogue states it plainly: past the maximum length, docking is required and the joint has to be reviewed with drawings. That number is around 6 m for the shaft profiles.

Consequence the carriage crosses the joint every stroke
Risk a step at the joint becomes an impact, not a roll
Rule put the joint outside the working stroke, or accept a slower axis

A joint in the middle of the stroke is the same problem as a badly made butt joint on a square rail, and the fix is the same: keep it out of the travel, or slow the carriage where it crosses.

04Load and moment, the two checks

For a twin-shaft carriage, the load check is simple: the sum of the two shaft capacities. The moment check is not, because the carriage can pitch on the pair:

Pitch MP = F × l, measured from the centre line between the shafts
Yaw MY = F × k, the lateral offset from that centre line
Roll MR = W × h, the centre of mass above the shafts

The wide stance helps yaw and roll and does little for pitch. A cantilevered head on a twin-shaft beam still needs a long carriage or a second pair.

05Where it fits and where it does not

  • Fits: long transfer beams, sliding gates, lift guides, test rigs, anything where the structure is a weldment and machining a rail face is expensive.
  • Fits: dirty environments, because the shafts can be wiped and replaced without re-grinding a rail.
  • Does not fit: precision positioning below a few hundredths, where the profile's straightness and the ball fit set the limit.
  • Does not fit: a single-rail axis, because the profile needs its full width anyway.

06Questions we get

When do two shafts beat one square rail?

When the axis is long, dusty and moderately loaded but still needs moment capacity, and when the structure can carry an aluminium profile instead of a machined steel face.

Why is the maximum length 6 m?

Transport and straightness. Past it the catalogue calls for docking, which puts a joint under the carriage every stroke; that joint has to be planned, not improvised.

Roller or ball on a shaft?

Rollers carry more for the same shaft and run quieter at low speed, but tolerate less misalignment and dirt. Balls are smoother and cheaper.

07Where to go next

All guides are listed on the knowledge index and grouped on the knowledge hub. The geometry decision is on cylindrical against square; the shaft side on linear shaft selection; the joint rule on butt joints.

Products: linear guideways. Send the beam length, the head mass and the joint position, and we will confirm the profile and the carriage.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts