One housing

Combined transmission blocks: screw, support and motor in one housing

A conventional screw axis has three parts in a row: the fixed-end support, a spacer or bracket, and the motor flange. Each joint adds an alignment error. An integrated block machines all three in one housing, so the motor pilot and the screw bore share a datum.

HM 12–30 MGD · MC 5 min read

01What the block integrates

  • Fixed-end bearing pair with lock nut and seal, already installed in the housing.
  • Motor pilot bore machined from the same datum as the screw bore, so the coupling has no offset to absorb.
  • Nut bracket interface on the moving side, or a separate bracket when the nut has to float.

The catalogue describes the result directly: the carriage assembly is installed without adding a fixed side, the motor is located by the embedding section, and the screw side and motor side are one piece, which suppresses the axis deviation between them. That is a manufacturing statement, not a marketing one: the alignment that used to depend on the assembly now depends on the block.

02The two families on the moving side

PartBehaviourWhen it belongs
HM integrated blockSupport, housing and motor pilot in one castingCompact axes, servo and stepper drives, where the motor is chosen with the axis
MGD nut blockFixed-position nut bracket, bolted to the carriageStandard build with a separate support seat
MC nut blockAdjustable nut bracketWhere the nut must be aligned to the rail after assembly

The HM range runs from HM12 to HM30 in the catalogue, with variants keyed to the motor flange — HM12-57 and HM12-60 are two different flange sizes on the same 12 mm class block. Read the suffix before comparing prices: the block, not the screw, is what changes.

03Sizing: screw first, then motor flange

1 Screw diameter and lead → the block class (12, 15, 20, 25, 30)
2 Servo or stepper frame size → the flange suffix
3 Motor shaft diameter and length → the coupling and the pilot depth
4 Stroke and critical speed → whether the block can carry the screw at all

The block class follows the screw, not the load: a 12 mm screw in a 20 class block is a mismatch of bore and bearing. The flange suffix follows the motor, and the two are independent, which is why the code carries both.

04The trade: stiffness against flexibility

An integrated block is stiffer and more accurate, and it removes two joints that used to absorb tolerance. That cuts both ways:

PropertyIntegrated blockSeparate parts
Axial runoutSet by one machining datumSet by the assembly, varies with the fitter
Assembly timeLow; no shimming of the motorHigher; coupling alignment needed
Change a motorNew block or machined adapterNew bracket only
Thermal growthMust be absorbed elsewhereCan be taken at the bracket joint

A long screw grows with heat. If both ends are fixed in one rigid line, that growth has to go somewhere: into the bearing preload, the coupling, or the nut. On a long axis, prefer one fixed end and let the other end float, even when the fixed end is an integrated block.

05Installation order

  1. Mount the block on the machined face first; it is the datum for everything after.
  2. Insert the screw and set the lock nut at the specified torque.
  3. Fit the coupling with the motor shaft free, then bring the motor into the pilot bore.
  4. Check axial play at the nut, not at the motor.
  5. Run the axis at low speed and listen for a once-per-turn sound, which is misalignment, not preload.

06Questions we get

What does an integrated block actually remove?

The joint between the fixed-end support and the motor bracket. In a conventional build that joint's alignment error becomes axial runout; in an integrated block both sides share one datum.

When is a separate nut bracket better?

When the nut has to float, when thermal growth must be taken up at a joint, or when the motor may change later. MGD is fixed position, MC is adjustable.

Does the block fix the motor centre height permanently?

Yes. The block is machined for a specific motor flange and screw diameter, so a later motor change may mean a new block. Confirm the flange drawing before ordering.

07Where to go next

All guides are listed on the knowledge index and grouped on the knowledge hub. The screw code is decoded on ball screw part numbers; the fixed end on support seats; the axis on module selection.

Products: ball screw category. Send the screw diameter, the motor flange drawing and the stroke, and we will confirm the block class and the flange suffix.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts