HM Integrated Motor Seat: Screw, Rail and Bearing in One Body
Key Features
One body replaces four seats: motor seat, coupling housing, bearing seat and nut block, with the bearing pair preloaded at the factory.
Applications
MS Linear Technical Support
Transmission Blocks · HM Integrated Motor Seat: Screw, Rail and Bearing in One Body
Technical Description and Selection ReferenceProduct Overview
The HM series is an integrated transmission block: motor seat, coupling housing, fixed-end bearing seat and nut block are machined into one body, so the screw, the rail and the motor are aligned before anything is bolted to the machine frame. The usual assembly steps, and the usual source of misalignment, disappear.
Models are named by screw diameter and motor flange: HM12-57, HM15-80, HM20-130, HM35-180 and the sizes between. The number after the dash is the motor flange size, so a 130 mm flange motor and a 40 mm screw point to HM40-180 rather than to a stack of separate seats.
For a machine builder the gain is time: one part replaces four, and the axis accuracy comes from the block, not from the fitter. The transmission block guide covers when the integrated block is worth the extra cost and when separate seats are still the better buy.
| Parameter | Specification |
|---|---|
| Series | HM integrated transmission block |
| Model logic | HM + screw diameter + motor flange, e.g. HM20-130 |
| Covered sizes | HM12-57, HM12-60, HM15-57, HM15-60, HM15-80, HM15-86, HM20-80, HM20-86, HM20-110, HM20-130, HM25-130, HM30-130, HM35-130, HM35-180, HM40-180 |
| Included parts | Motor seat, coupling housing, fixed-end bearing seat, nut block |
| Bearing | Angular contact pair, preloaded |
| Screw fit | Matched to the screw diameter in the model code |
| Motor fit | Matched to the flange size in the model code |
| Alignment | Set by the block; no separate seat alignment |
| Mounting | Bolted to the machine plate; rail and screw fitted after |
| Lubrication | Bearing grease pre-filled |
| Minimum order | 1 piece |
| Lead time | 10–15 days, drawing and motor flange required |
Product Features
- One body replaces four seats, so the axis is aligned by the part rather than by the fitter.
- Preloaded bearing pair is fitted at the factory, removing the preload setting step.
- Motor flange is part of the model code, so a mismatched motor is caught at order time.
- Rigid body resists the bending that separate seats allow under fast reversal.
- Shorter assembly time on the machine frame, which is the real cost saving.
Applications
Where the axis is built around one screw and one rail, the integrated block removes a whole assembly step. For separate seats, see the MGD nut block and MC nut block.
About MS Linear
MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.
Next
MGD Fixed Nut Block: Square Housing for DSG Screw Nuts
Read before you specify
Frequently Asked Questions
The HM body combines the motor seat, the coupling housing, the fixed-end bearing seat and the nut block in one part. The bearing pair is fitted and preloaded at the factory, so the screw, rail and motor are aligned by the block rather than by the fitter.
HM plus screw diameter plus motor flange: HM20-130 is a 20 mm screw with a 130 mm motor flange, HM40-180 a 40 mm screw with a 180 mm flange. Send the screw diameter and the motor drawing, and the code is confirmed before production.
The MGD fixed block is for a machined plate where the stack height is already set. The MC adjustable block adds a small height trim, which absorbs the difference between a machined plate and a real assembly. Use the fixed block when the plate is right, the adjustable one when the screw centre is fixed and the plate is not.
Yes. Transmission Blocks can be shipped as a set with the screw, the nut and the support seats, with the end journals machined to the block. That keeps the thread, the bearing seat and the nut concentric.
Standard codes dispatch in 3–10 days. A non-standard motor flange needs the motor drawing and adds machining time, typically 15–20 days (2–3 weeks); the date is confirmed in the quotation.
Buying Transmission Blocks from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
