Axial location

Ball screw support seats: fixed end and supported end

The nut moves the load; the support seats decide whether the screw can push it without moving first. One end carries the axial load and sets the datum, the other only holds the screw up. Getting the pair and the grade right is worth more than one accuracy step on the screw.

BK · FK · EK · AK BF · FF · EF · AF 5 min read

01What a support seat actually does

The fixed end holds the screw in axial position and takes the thrust from the nut. That means a bearing pair that can carry load in both directions, a lock nut that sets the preload, and a housing rigid enough not to move under that thrust. The supported end carries only the radial weight of the screw, and often nothing else.

The consequence: the fixed end is a precision component, the supported end is a support. Money spent on a preloaded fixed end buys axial stiffness; money spent on a supported end buys very little.

02The two families and their pairs

EndSeriesConstruction
FixedBK, FK, EK, AKAngular-contact pair, preloaded at C5 or set with clearance at C7; lock nut and collar included
SupportedBF, FF, EF, AFSingle radial bearing, no axial location; simple housing

The letters pair by housing style — BK with BF, FK with FF, EK with EF, AK with AF — so the two ends of one screw share a family look and a mounting pattern. The suffix is the shaft diameter: BK10 for a 10 mm screw, BK20 for a 20 mm screw. Confirm the housing outline and the journal dimensions in the size drawing before designing the bracket, because the same suffix can differ between families.

03The bearing arrangement follows the screw grade

This is the part that gets skipped, and it decides how much axial play the axis really has:

Screw and seat gradeBearing arrangementAxial clearance
C7 with EK05–EK08Deep-groove ball bearingAbout 0.03 mm; light axial load only
C7 with EK10–EK20Angular-contact pair, not preloaded0.018 mm maximum
C5Angular-contact pair, preloaded at the factoryZero

A C7 seat on a C5 screw leaves play at the support; a C5 seat on a C7 screw is wasted money unless the screw is also upgraded. Match the seat to the screw, and write both on the drawing.

04Sizing the seat: diameter first, then load

The seat is chosen by shaft diameter, and then checked for the axial load it will see. The axial load is not the machine's payload: it is the thrust needed to move the load plus the preload in the nut plus the inertia of the screw itself during acceleration.

Thrust F = friction + cutting force + m × a
Seat load F_seat ≈ F, plus the nut preload when the screw is preloaded
Check F_seat against the seat's dynamic rating, not its static rating

A small seat on a large screw is a common mistake in reverse: the housing fits the bracket, the bearing does not fit the thrust. If the calculated thrust is close to the seat rating, step the seat family rather than hoping.

05Mounting details that decide whether it runs true

  • Journal fit. The screw journal is ground to the seat's bore; a seat re-machined to fit a worn journal loses concentricity.
  • Lock nut. Tighten against the collar with the specified torque; a loose lock nut lets the bearing pair walk and the preload disappears.
  • Squareness. The seat face must be square to the screw axis, or the screw runs in a circle and loads the nut every turn.
  • Alignment with the motor. The motor bracket and the seat share the datum; a coupling misalignment shows up as axial vibration at speed.

06Failure modes and what they look like

SymptomLikely causeFix
Backlash at reversalC7 seat with clearance, or loose lock nutPreloaded seat, or reset the nut
Whine rising with speedSeat face not square; bearing preloaded by misalignmentRe-shim the seat, check the bracket
Grease leaking at the housingSeal damaged during assemblyReplace the seal, check the journal burr
Axial play that growsHousing fretting, or the seat was sized below the thrustStep the seat family, re-check the thrust

07Questions we get

Does BK10 mean a 10 mm screw?

Yes. The suffix is the nominal shaft diameter the seat is machined for. The seat also fixes the journal and the lock-nut thread, so a mismatch cannot be corrected with an adapter.

Can both ends be fixed?

Possible, and used on long, fast or vertical screws, but it is a different design: two preloaded ends fight each other as the screw grows with heat. The usual arrangement is one fixed end and one supported end.

Why does a C7 seat have axial clearance?

The bearing pair is not preloaded at that grade: 0.018 mm maximum for the angular-contact versions, about 0.03 mm for the small deep-groove ones. That play belongs to the support and adds to the lost motion of the axis.

08Where to go next

All twenty guides are on the knowledge hub. The screw code that pairs with these seats is decoded on ball screw part numbers; the module that packages both is on linear module selection; the life arithmetic is on life correction, and the load and life calculator takes the numbers.

Products: ball screw category. The guideway FAQ covers the general questions. Send the screw diameter, the thrust and the grade, and we will confirm the fixed-end and supported-end pair before quoting.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts