Environment

Guideway dust protection: wiper codes, metal scrapers and covers

Sealing is chosen from the contamination, not from the price list. The three regimes below need different hardware, and fitting the wrong one is how a rail that was correctly sized ends up worn out in a year.

ZZ · KK · DD Scrapers and bellows 5 min read

01Three contamination regimes

RegimeTypical sourceWhat it does to a block
Dry, hard chipsCast iron, brass, wood dust, composite trimmingCuts the wiper lip, then grinds the raceway. Wear is fast and local, usually on the side facing the cut.
Wet, fine particlesCoolant mist, washdown, graphite or carbon dust with oilForms a paste that holds particles against the raceway. Corrosion starts under the seals where the paste sits.
Very fine abrasiveGrinding dust, polishing compound, ceramic powderPasses a single rubber lip and polishes the raceway. Damage is slow, uniform and shows up as lost preload rather than as noise.

The regime decides whether the answer is a better wiper, a metal scraper, a covered rail or a full bellows. Buying a higher sealing code when the problem is wet paste, or a bellows when the problem is one hard chip per cycle, both waste money.

02What the sealing codes actually add

Codes vary between catalogues, but the order of protection is consistent. On most series:

CodeConstructionBest for
StandardRubber wiper, seal, bolt-hole capsClean room-side machinery, light dust.
ZZWiper plus a metal scraper ahead of the rubber lipDry chips and swarf: the scraper takes the impact, the rubber takes the fines.
KKDouble wiper with an abrasion-resistant seal and a metal scraperContinuous chip flow and moderate coolant; the usual choice for general machining centres.
DDDouble wiper plus a debris cover over the block entryHeavy chip load and washdown, where chips arrive in bulk rather than one at a time.

Each step adds drag as well as protection. A DD block on a clean high-speed axis runs hotter and consumes more drive force for no benefit, so the code should match the machine's actual environment rather than the worst case imagined in the specification.

03The five layers, from cheapest to most complete

1

Wiper quality

The first line. A worn lip lets everything else through, so wiper inspection belongs in the maintenance schedule, not in the spare parts list.

2

Metal scraper

A hard plate ahead of the wiper that takes the impact of chips. Cheap, replaceable, and the single most effective upgrade on a dry-chip machine.

3

Bolt-hole caps and end caps

Open bolt holes are contamination paths into the raceway. Caps are usually included but are often lost during service.

4

Covered rail

A rail with a cover strip over the raceway, as on covered-roller series. The cover protects the rail between passes, and the block lifts it as it travels.

5

Bellows or telescopic cover

Whole-axis protection for grinding, casting and food lines. It keeps the bulk off the rail, but needs venting and a drain path or it becomes a moisture trap.

04Choosing by environment

EnvironmentRecommendation
Machining centre, flood coolantKK or DD plus a drain path at the rail ends. Check the wiper at every relubrication; coolant paste is the usual failure route.
Cast iron or graphite dry cuttingMetal scraper plus ZZ at minimum; a covered rail if the chips fall directly onto the rail.
Grinding or polishingBellows cover over the whole stroke, with a sealed block underneath. Fine abrasive passes any single lip.
Woodworking and panel sawsMetal scraper and frequent wiper replacement; sawdust is dry, abrasive and arrives continuously.
Cleanroom and laboratoryStandard sealing; the risk is particles generated by the block itself, so low-drag and low-emission configurations matter more than heavy sealing.

05Maintenance that actually protects the rail

  • Inspect, do not just top up. At every relubrication, look at the wiper lip and the grease behind it. Dark, gritty grease means the seal has already failed.
  • Replace wipers in pairs. A new wiper beside a worn one leaves one side of the raceway unprotected and loads the block unevenly.
  • Keep the cover clean. A bellows full of chips abrades the rail every stroke. Clean it on the same schedule as the wipers.
  • Do not over-grease to compensate. Extra grease pushed out at the ends collects chips and forms the paste that the seal is trying to keep out.

Sealing and lubrication are one system: the grease fills the gap behind the wiper and the wiper keeps the grease in place. Treating them as separate maintenance items is what produces a block that is both dry and contaminated.

06Questions we get

Is a double wiper enough for cast iron chips?

Usually not on its own. A metal scraper ahead of the seal, or a covered rail, is what keeps hard chips off the raceway.

Does a bellows cover replace a sealed block?

No. The cover handles the bulk, the wiper handles the film. The block still needs its own seal, and the cover needs venting.

How often should wipers be replaced?

Inspect at every relubrication and replace when the lip is scored, hardened or no longer in contact. On a dirty line that can be months.

07Where to go next

Sealing works with the grease: lubrication interval and fill procedure covers what sits behind the wiper. Accuracy and preload explains why contamination shows up as lost preload first, and the noise page covers what a dry wiper sounds like before it wears the rail, and installation covers the bolt-hole caps that are usually the first thing lost.

Rails with protection built in: CRG covered roller, SE metal end cap, stainless series for washdown.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts