Knowledge library
Linear motion knowledge, arranged by the decision you are making
Thirty-four technical guides selected from our selection materials and application work. Each one answers a single question on the way from a load case to a part number, so you can read the page you need instead of the whole manual.
01 · Start here
The four pages most first-time buyers need. Together they take a load case from a sketch to a size and a part number.
How to select a linear guideway
Six steps: collect the load case, pick the family, size from C against the target life, then grade, preload, length and lubrication.
Read the guide ToolGuideway size calculator
Enter the load per carriage, stroke and rail layout; get the load per block, the required C and an L10 in kilometres.
Open the calculator ToleranceAccuracy grades and preload
What C, H, P, SP and UP control, what Z0, ZA and ZB change, and the four pairings that cover most machines.
Read the guide Contact typeBall or roller guideway
The same 20 kN load case on both contact types, with the life bases, rigidity and the four signals that favour rollers.
Compare the two02 · Load and life
Once the size is shortlisted, these four pages decide whether the rail will last: the ratings by size, the peak check, the duty-cycle mean, and the correction factors the catalogue leaves out.
Size chart, 15 to 65
Static and dynamic ratings for ball and roller at eight sizes, plus the smallest size for a given load at two safety factors.
Read the guide PeakMoment load and overhang
MR, MP and MY, the M = F × l calculation, a 900 kg gantry worked through, and the four ways to cut the moment.
Read the guide Duty cycleMean load
Why the peak is the wrong number for life, the stepped, linear and sinusoidal formulas, and a conveyor worked through.
Read the guide Rating lifeLife correction: fh, ft, fw
Hardness, temperature and load factor, with the same conveyor duty corrected from 851 km down to 252 km.
Read the guide03 · Running the axis
The installation and maintenance side: what the drive has to push, how the rail is lubricated, aligned, jointed and protected, and why the axis gets noisy.
Friction and drive force
Ball 0.004 against roller 0.003, seal drag, horizontal, vertical and inclined cases, and the motor margin to keep.
Read the guide MaintenanceRelubrication interval
The 100 km rule, grease against oil at 60 m/min, the hours conversion at six speeds, and the fill procedure.
Read the guide AssemblyInstallation sequence
Master rail and datum edge, four side-push methods, the seven-step order, and the five symptoms of a bad assembly.
Read the guide Long strokeRail joints
Where a joint should sit, why the two rails are staggered, the assembly order, and what a bad joint sounds like.
Read the guide Machine bedMounting surface tolerance
Flatness and two-rail parallelism by grade, four ways to measure, and what to do when the bed is out.
Read the guide LayoutMounting orientation
Horizontal, wall, inverted and vertical: where gravity goes, which moment dominates, and what changes in upkeep.
Read the guide EnvironmentDust and chip protection
Standard, ZZ, KK and DD seals, metal scrapers, covered rails and bellows, matched to chips, coolant and fine dust.
Read the guide DiagnosisGuideway noise
Recirculation ring, joint click, wiper rub, frame resonance, and the order to fix them without changing parts blindly.
Read the guide FamilySeries comparison
All guideway families on four axes, the five-step choice order, and the five mis-selections we see most.
Read the guide ReplacementReplacement cross-reference
Map a part number on your drawing to the right family, then the four dimensional checks before any swap.
Read the guide04 · Special formats
The rail, the material, the noise target and the family choice each change the shortlist. These eight pages cover the cases where the standard families stop being the obvious answer.
Miniature guideways, size 7 to 15
Moment dominance, TGN against TGW, M2 to M4 screw torque, dust-sheet clearance and rail end distance.
Read the guide Single trackWide rail guideways
When one track replaces two rails, what it does to mounting height, and the length at which it stops working.
Read the guide MaterialStainless steel guideways
9Cr18 at HRC 55 against GCr15 at HRC 60-62: what it buys, what it gives back, where it is the only choice.
Read the guide ComparisonTGH against TGL
Same rail, same rating, 4 to 10 mm of height. Where the low-profile block wins and where the taller section still earns its place.
Read the comparison ComparisonCA against HA
The long carriage adds a fifth of dynamic rating and a third of static, and takes 15 to 38 mm of carriage length out of the stroke.
Read the comparison ComparisonDG against TG
24 to 42 mm of carriage height against the family above it, and the matched-set consequence for spares.
Read the comparison AcousticsSilent guideway selection
Four noise sources, three the block controls: how to tell which one is yours before paying for the wrong series.
Read the guide05 · Beyond the rail
An axis is a rail plus a screw, a support, a shaft and a bearing. These six pages cover the parts that sit around the guideway, and the one comparison that decides whether a guideway is needed at all.
Ball screw part numbers
Nine segments from thread direction to preload, the circulation letters, and the grade that the support unit has to match.
Read the guide AxisLinear module selection
Four inputs, the YD rail lengths, the critical speed that caps a long stroke, and the moment check at the end of travel.
Read the guide SupportSupport seats, both ends
BK, FK, EK and AK against BF, FF, EF and AF, and the 0.018 mm and zero-clearance bearing arrangements behind them.
Read the guide ShaftLinear shaft selection
Hardness grades, hollow sections, and the deflection rule that decides support spacing before diameter.
Read the guide GeometryCylindrical against square
The structural difference, the moment case that rules a shaft out, and the alignment labour quotes tend to leave out.
Read the guide BearingLinear bearing selection
Adjustable against fixed clearance, the long bodies that add moment capacity, and the h6 / H7 fit behind the rattle.
Read the guide06 · Holding and mounting
Four pages about the interfaces around the moving part: how a block, a clamp, a twin-shaft profile and a flange change what the axis can hold and how it is assembled.
Combined transmission blocks
Screw support and motor pilot in one housing: the alignment it removes, and the motor change it makes harder.
Read the guide HoldingLocking guideways
TGR rails and clamps from size 15 to 55, the stroke they cost, and when a motor brake is the better device.
Read the guide Twin shaftHeavy cylindrical guides
SBR, TBR and SGR: two shafts in one profile, the moment they carry, and the 6 m line where docking begins.
Read the guide FlangeFlanged linear bearings
Square and round flanges, body length as moment capacity, and the plate rules that stop the bearing tilting.
Read the guide07 · Buying and delivery
Browse by product line
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Not sure which page applies to your axis?
Send the drawing, the load and the stroke. We reply with the family, the size, the grade and a corrected life figure within one business day.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
