Four inputs

Linear module selection: stroke, load, speed, grade

A module is a rail, a screw, a nut and a carriage sold as one part, which makes selection simpler and less forgiving at the same time. Four inputs decide the size; three checks decide whether the size you picked will actually run.

YD 40–130 Critical speed 6 min read

01The four inputs, in order

  • Stroke. Usable travel, not rail length. It sets the screw span and therefore the speed limit.
  • Load. Moving mass plus payload, and where it sits relative to the carriage. An offset load turns into a moment.
  • Speed. The fastest move in the cycle, and the acceleration that gets it there. A module that reaches the speed but not the acceleration is the wrong module.
  • Grade. Positioning accuracy and repeatability the process needs; this picks P or C and, with it, the screw class and the support bearings.

Get these four in writing before opening the catalogue. Most mis-sized modules come from a stroke quoted as rail length and a load quoted without the fixture.

02The YD range and its standard lengths

SizeStandard rail lengths, mmWhat it suits
YD40100, 150, 200Short pick-and-place heads, sensor moves
YD50150, 200, 250, 300Small gantries, dispensing
YD60150, 200, 300, 400, 500, 600The common automation size; the widest length choice
YD86340, 440, 540, 640, 740, 940Medium gantries with a cantilevered head
YD100980, 1080, 1180, 1280, 1380Long travel, heavier payload
YD130980, 1180, 1380, 1680Heavy gantry axes and transfer units

Lengths step in fixed increments, and a non-standard length is a new screw and possibly a new rail. Where the stroke lands between two steps, take the longer one and use the extra travel as end clearance rather than shortening the screw.

03Speed is set by the screw, not the motor

The table speed follows directly from screw speed and lead:

Linear V (mm/s) = S (rpm) / 60 × L (mm per turn)
Ceiling S is limited by the critical speed of the screw span
Result a longer module has a lower top speed at the same lead

This is the single most common surprise in module selection. A YD60 at 300 mm stroke and a YD60 at 600 mm stroke do not share a maximum speed, because the screw span doubled and the first critical speed fell with the square of the length. The catalogue lists the maximum speed per length for that reason.

Two ways out, both with a cost:

  • Larger lead. More travel per turn at the same screw speed, but less resolution and more torque per unit of thrust.
  • Larger screw diameter. Raises the critical speed, but adds inertia and cost, and often means the next module size.

04Accuracy, repeatability, parallelism

Three figures are quoted, and they are not the same promise:

FigureWhat is measuredWhy it matters
Positioning accuracyDifference between commanded and reached position over full travelMatters when the process is programmed in absolute coordinates
RepeatabilityScatter when returning to the same pointMatters when the process teaches its own positions, which is most assembly work
Travel parallelismHeight variation of the carriage over the strokeMatters when a tool is mounted on the carriage and the gap has to stay constant

The catalogue grades are P and C. In practice, a P module is quoted with repeatability in the low single micrometres and a C module around a hundredth of a millimetre; confirm the exact figure for the size, because it changes with stroke.

05Load, moment and the number of carriages

A module carriage is short. That makes it convenient and makes it sensitive to pitch and yaw:

Pitch MP = F × l, l from the rail centre to the load line
Yaw MY = F × k, k the lateral offset
Roll MR = W × h, h the height of the centre of mass

Two carriages on one module double the moment base and are the cheapest fix for an offset head. Check the static permissible moment for the size, with a factor of 1.5 to 2.0, and then check the life with the mean load rather than the peak. A module that passes the static check and runs at 70% of C will not make the maintenance interval.

06Duty cycle and acceleration

The motor is sized from the cycle, not from the top speed. Write the move as accelerate, run, decelerate, dwell, and calculate the torque in each phase; the acceleration phase usually sets the motor because it carries both the inertial force and the friction.

ParameterTypical automation valueConsequence if exceeded
Acceleration0.15–0.3 GImpact at reversal, rail noise, shortened life
Duty cycle0.5 standardMotor and screw heat, grease breakdown
Reversals per minuteSet by the processRecirculation wear; the block, not the motor, is the limit

Fast cycles also raise the load factor fw in the life calculation, so the same payload at 0.3 G consumes life faster than at 0.15 G. That is the connection between the cycle and the life correction page.

07Mounting, motor and the parts around it

  • Mounting face. The module base is the datum; a twisted plate twists the rail. Flatness and straightness of the mounting face matter more than the module grade.
  • Motor interface. Coupling, bracket and bearing support are usually bought with the module; mismatched brackets are a common source of axial preload on the screw.
  • Cable and guard. The carriage moves the cable; a stiff cable bundle can load the carriage sideways over a long stroke.
  • Limits. Fit hard stops outside the working stroke, not at it, and keep the shock away from the screw end.

08Questions we get

Why does a longer module have a lower speed limit?

Because the screw is a shaft: as the span grows its first critical speed falls, and the nut cannot be driven past it without resonance. The catalogue speed is per length, not per size.

Positioning accuracy or repeatability?

Accuracy is how close the table gets to the commanded point; repeatability is how consistently it returns. Repeatability is usually an order of magnitude better and is the figure that matters when the process teaches its own positions.

Can two modules be stacked?

Yes, but the lower module carries the upper module plus its payload, cantilevered. Check the moment at the end of the upper stroke, not at the centre.

09Where to go next

All twenty guides are on the knowledge hub. The screw inside the module is decoded on ball screw part numbers; the fixed and supported ends on support seats; the moment check on moment load, and the arithmetic on the load and life calculator.

Products: single-axis robots. The guideway FAQ answers the sizing questions that come before a quotation. Send the stroke, the moving mass, the cycle time and the required repeatability, and we will return the size, the lead and the grade.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts