Long stroke

Joining two guideway rails: joint position, stagger and symptoms

Past a certain length, a rail arrives in sections. The joint is not a defect if it is placed and aligned properly, and it is the first suspect when a long axis clicks, wanders or wears in one spot.

Joint placement Staggered pairs 5 min read

01When a single rail is no longer practical

Two limits decide this, and neither is the load rating:

  • Transport. A rail that will not fit through the door or onto the truck has to be split, whatever the machine needs.
  • Manufacturing. Grinding, straightening and inspecting a very long rail in one piece is harder than making two shorter ones and matching them.

A joined rail is supplied with ends that have been prepared for the joint: the cut faces are square, the ends are numbered, and the rail is marked with arrows showing the direction of assembly. Those marks are the installation instructions and should not be cleaned off.

02Where the joint should sit

Three placement rules, in order of importance:

RuleReason
Away from the stroke endsThe ends are where the block changes direction and where the wiper is most likely to be half off the rail. A joint there is crossed twice per cycle at the worst moment.
Out of the acceleration zoneThe block crosses a joint under the highest side force during acceleration. Keep the joint in the constant-velocity part of the stroke where possible.
Not under a dwell positionA block that stands still on a joint for most of the cycle loads one edge of it continuously and wears a step into the rail.

The exact position is a layout decision, not a catalogue number. Put the joint where the block spends the least time and crosses it at the lowest speed.

03Stagger the pair

On a two-rail axis, the two rails must not share a joint station. If they do, the block assembly crosses both discontinuities at once, and the two geometric errors add instead of being absorbed by the structure.

Stagger so that at any point in the stroke only one block is on a joint. With four blocks and a table of length L, that usually means separating the joints by at least a table length, and preferably by a few hundred millimetres on either side of that.

Check it on the drawing. Mark the joint positions and the block positions at the two stroke ends. If a joint falls inside the block footprint at either end, move it; that is the configuration that produces a click once per pass.

04Assembly order at the joint

1

Respect the numbers

Sections are numbered and the arrows show the assembly direction. Assembling them out of order or backwards mismatches the ends that were prepared as a pair.

2

Seat the first section

Fix it against the datum and torque it as for a normal rail. The joint is measured from a rail that is already correct, not from one that is still floating.

3

Bring the next section in

Slide it up to the joint with the faces in contact, check the gap with a feeler gauge, and clamp it against the datum before torquing.

4

Check across the joint

Run a dial indicator along the rail face across the joint, or slide a block across it by hand. Any step, click or change in force is a joint that needs another pass.

05Three symptoms of a bad joint

SymptomWhat it meansWhat to check
Click once per passA step at the joint, in height or in alignment.The joint gap, the squareness of the cut faces, and whether both rails share the joint station.
Waviness in the finishThe block is following a periodic error as it crosses the joint.Indicator reading across the joint, and whether the sections were assembled in numbered order.
Local wear at one spotThe block dwells on the joint, or one edge of the joint is taking the load.Joint position relative to the dwell point and to the acceleration zone.

A joint that is merely noisy but geometrically clean is usually a wiper catching the gap. A joint that produces a measurable step is an assembly error, and no amount of running-in will remove it.

06Questions we get

At what stroke length does a guideway have to be joined?

It depends on the transport limit and on the length the supplier can grind and inspect in one piece, not on a fixed number. Most catalogues stop a single rail somewhere between two and four metres.

Can two rails share the same joint position?

They should not. Shared joints make the block cross both discontinuities at once, and the two errors add.

Does a joint reduce the load rating?

The rail keeps its rating; the joint is a local geometric discontinuity. It affects accuracy, noise and local wear rather than the nominal C value.

07Where to go next

The joint is the last step of a longer sequence: installing a guideway covers the datum and the alignment that the joint has to match. Mounting surface flatness explains why a joint looks worse on a bed that is not flat, and accuracy grades gives the tolerance the joint has to meet for each grade.

Long-stroke rails for gantries: HG series, WE wide rail. Covers for exposed joints on dirty lines: CRG covered roller.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts