01One question decides everything
Before the series, the size or the preload, ask where gravity goes. On a horizontal rail it presses the block into the raceway, which the bearing is designed for. On a wall it runs along the rail and never touches the rolling contact. On an inverted rail it pulls the block away from the rail, which is the one case the bearing is least comfortable with. Every other difference follows from that.
| Orientation | Gravity path | What it loads |
|---|---|---|
| Horizontal | Into the raceway | Radial load plus the moment from centre-of-gravity height. |
| Wall (rail vertical) | Along the rail | Drive and brake take the weight; the block sees the offset load and a yaw moment. |
| Inverted | Away from the rail | Lift-off on the upper row; preload and retainers carry the suspended mass. |
| Vertical (rail upright) | Along travel | Axial load on the drive, plus a pitch moment from any offset head. |
02Horizontal: the design case
This is what the catalogue numbers describe. The weight sits on four blocks, the centre of gravity is above the rail plane, and the moment that matters is W × h spread over the rail spacing c. Two things are worth checking rather than assuming:
- Where the mass actually is. A gantry with the head at the end of a 1.2 m arm puts most of its load on two blocks, not four, and the pair carries a roll moment that the nominal W/4 figure does not show.
- Whether the table is rigid. Four blocks on a soft plate behave like three, because the plate deflects and one corner unloads. The moment calculation in moment load assumes a rigid table.
A horizontal axis is also the easiest to lubricate: grease stays where it is put, and a missed interval usually shows up as a slow increase in drag rather than a sudden failure.
03Wall-mounted: gravity goes to the drive
Mount the rail on a vertical face and the carriage travels horizontally, but the weight now hangs off the rail rather than resting on it. The rail is not carrying the mass; the ball screw, the belt or the brake is. Two consequences follow immediately:
- A holding brake is not optional. Power off, a vertical wall axis with a ball screw will back-drive under its own load. The brake belongs in the drive train, and the rail should not be used as the stop.
- The moment is a yaw moment. The load centre hangs at some distance from the rail plane, so the block is twisted around the vertical axis. Spacing two blocks along the rail helps far more than increasing the size, because the yaw arm is the distance between them.
Preload for a wall axis is usually one step higher than the horizontal equivalent, because the load reverses every stroke and nothing is seating the block. ZA rather than Z0 on most automation, ZB where the head is long.
04Inverted: the case that catches people
Rail above, block hanging below, load suspended. Now gravity pulls the block away from the rail and the upper row of balls or rollers is unloaded. The block does not fail from overload; it fails from rocking, from the retainer taking a load it was never meant to take, and from grease migrating out of the contact.
- Light preload is the minimum. ZA removes the play that would otherwise let the block rotate under the suspended mass; Z0 on an inverted axis is a rocking assembly waiting to happen.
- Add a mechanical catch. A second rail, a guide roller or a captured block. A preload is a spring, not a safety device, and a dropped load is a different risk category from a worn rail.
- Shorten the grease interval. Gravity works against the grease in an inverted block. Use the interval for a wall axis as the starting point and inspect after the first weeks rather than the first year.
05Vertical travel: axial load on the drive
A vertical axis is a wall axis rotated ninety degrees: the rail is upright, the carriage moves up and down, and the weight is carried along the rail by the drive. The raceway sees very little radial load, which is why a vertical axis with ZB preload is often over-built for no benefit.
What matters here is the pitch moment from the head hanging off the carriage, and the behaviour at reversal. On the way up the drive pushes; on the way down gravity pulls and the screw may be in tension rather than compression. If the axis has a counterweight or a brake motor, the load on the rail changes sign at reversal, and that is the case to calculate rather than the steady one.
Counterweight or brake.
A counterweighted vertical axis behaves like a much lighter one for the drive, but the rail still sees the full mass during acceleration. Do not size the rail from the counterweighted figure.06What changes with orientation, in practice
| Item | Horizontal | Wall / inverted / vertical |
|---|---|---|
| Preload | Z0 to ZA for most automation | ZA minimum; ZB for long or heavy heads |
| Dominant moment | Roll, from CG height | Yaw on a wall, pitch on a vertical axis |
| Lubrication | Standard 100 km interval | Shorten; grease drains away from the contact |
| Wiper | Standard wiper | Add a scraper on the upper face; chips settle on a wall rail |
| Safety | Mechanical end stops | Holding brake plus a catch; a dropped load is not a wear problem |
07Installation notes that only apply off-horizontal
The installation sequence itself does not change: master rail first, push against the datum, torque from the centre outwards, then the second rail. What changes is the reference. On a wall, the datum edge is usually the bottom edge, because that is the edge gravity and the assembly will find; on a horizontal bed it is conventionally the side facing the operator. Write it down, because the two fitters on the next shift will otherwise pick different edges.
Alignment checks also change. A wall rail cannot be checked with a level; use the dial indicator bridge described in mounting surface and check parallelism in the plane that carries the load, not the plane that is easy to reach. And on an inverted rail, check the block retainers before installation: a block that has been dropped during handling may have lost balls, and on an inverted axis they fall out rather than sit quietly at the bottom.
08Questions we get
Do I need a different guideway for a wall-mounted axis?
Usually the same rail with a higher preload and a better wiper. Gravity runs along the rail and is taken by the drive, while the raceway carries the offset load and the yaw moment.
What fails first on an inverted axis?
Lift-off and rocking, not brinelling. The suspended mass pulls the block away from the rail, so light preload and a mechanical catch matter more than a bigger size.
Does orientation change the lubrication interval?
Yes on inverted and wall axes. Grease drains away from the contact, so the standard interval leaves the raceway drier; shorten it and inspect early.
09Where to go next
Installation sequence covers the master rail and the torque order; accuracy and preload explains what ZA and ZB actually change; relubrication has the interval arithmetic. If the axis is long and thin, moment load is the page to read before choosing a size.
Compact blocks for wall and inverted heads: EG low profile and QE silent low profile. For a vertical ram with side load: QH heavy load.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
