Running behaviour

Linear guideway noise: what the sound tells you

A carriage that can be heard across the shop is reporting one of four problems, and only one of them is solved by buying a quieter series. This page separates the recirculation ring from the joint click, the wiper rub and the frame resonance, then gives the order to fix them in.

Four sources Silent series limits Measurement 6 min read

01Four sounds, four causes

Listen before opening the catalogue. Each of these has a distinct character, and mixing them up leads to buying a component that cannot fix the problem.

SoundSourceFirst check
Continuous ring or hiss, rises with speedBall recirculation through the return pathSpeed sweep with the machine empty; compare a silent and a standard block on the same rail.
One click per stroke, always at the same positionRail joint or a step at the jointChalk the rail and mark where the click happens; check joint alignment with a dial indicator.
Soft rub, worse after a dry runWiper against the rail, or a dry racewayWipe the rail and re-lubricate; if it changes, it was the wiper or the grease.
Boom or rattle from the machine frameResonance of covers, guards or a loose mountingTouch the cover while it runs; if the sound changes, the rail is not the source.

02Recirculation: the speed-dependent part

Every ball leaves the loaded zone, enters a return path, and re-enters. At low speed that is almost silent. As speed rises, the ball passage frequency climbs into the audible range and the return path starts to act like a small pipe organ: the block rings at a frequency set by the number of balls passing per second and the geometry of the return.

Ball passage f ≈ V / (60 × ball pitch)
V carriage speed, m/min
ball pitch spacing along the raceway, m

You do not need the exact number to use this. The point is that the frequency scales linearly with speed, so the sound changes pitch as the axis accelerates, and it disappears when the axis stops. A noise that continues with the axis stationary is not recirculation.

Sound level rises roughly 5 to 6 dB per doubling of speed in the range where recirculation dominates. That is why the same machine is acceptable at 30 m/min and unbearable at 90, and why the fix is often a speed profile change rather than a different block.

03What a silent series actually changes

A "silent" block is not a different bearing principle. It is the same four-row geometry with three changes in the details that make the noise:

  • The return path. A smoother, wider return with a gentler entry angle, so the ball is accelerated less abruptly as it re-enters the loaded zone.
  • The end cap. Resin or a damped composite instead of metal, which absorbs the impact of the ball entering the return instead of ringing.
  • The ball retainer. A cage that keeps the balls spaced, so they do not collide as they bunch up at the return entry.

The effect is largest at low and medium speed, where the ring is most audible, and smallest at high speed, where the return is not the dominant source. A silent series does nothing for a joint click, a dry wiper or a resonating cover, and it does nothing for the drive train, which on many machines is louder than the rail.

Worth knowing. Silent series usually cost more and carry the same load ratings. If the machine already has a rail joint in the middle of the stroke, fix the joint first: that click will still be there after the upgrade.

04Joints, wipers and mounting

Joints. A click at the same position on every stroke is a joint, not a bearing. Either the two rail ends are not aligned within the running tolerance, or the joint sits in the acceleration zone where the load is highest. Both are installation issues; the position rules are in butt joint.

Wipers. A wiper that is dry, swollen or loaded too hard against the rail produces a soft continuous rub that gets worse as the rail collects dust. It is easy to test: clean and lubricate the rail; if the sound changes, the wiper is involved.

Mounting. A rail bolted to a thin plate, or a cover panel that touches the carriage, turns the rail into a soundboard. Isolate the cover, stiffen the plate, or accept that the noise is structural and no bearing change will help.

05Measure it before you change it

A sound level meter is cheap and a phone app is cheaper. Either is enough to compare before and after, which is what matters:

  • Microphone at 1 m from the rail, at carriage height, pointing at the block, not at the motor.
  • Machine empty, no workpiece, no cutting, so the measurement is the axis and not the process.
  • Three speeds: the lowest, the normal running speed, and the maximum. Record all three; one number hides the speed dependence that identifies recirculation.
  • Stationary baseline: same position, axis stopped, drive energised. Subtract nothing, but note it; if the baseline is already loud, the rail is not the problem.

Compare the three numbers. A rise that tracks speed is recirculation; a spike at one position is a joint; a floor that is high even when stationary is the drive or the frame.

06The order to fix it in

StepActionWhy this order
1Clean and relubricate the railRemoves the cheapest cause and gives a clean baseline.
2Check joint position and alignmentA click is never fixed by a quieter block.
3Inspect wipers and coversCheap to replace, and a dry wiper also wears the rail.
4Stiffen or isolate the frame and coversStructural noise survives every component change.
5Change to a silent seriesOnly now is the remaining noise actually recirculation.

On a new design the order is different: choose the silent series at the start if the machine is in a quiet environment, and place the joint away from the acceleration zone so the question never arises.

07Questions we get

Will a silent series make my machine quiet?

It removes the recirculation ring. It does not remove a joint click, a dry wiper, a loose cover or a drive train that is louder than the rail.

How loud is normal?

A clean, lubricated block on a straight rail is usually quieter than the drive and the process. If you can hear the carriage at 1 m over the machine, measure at three speeds before changing anything.

Does preload make a guideway louder?

Slightly, and predictably: more friction and a higher contact load add a steady hiss at speed. It is not a cure for joint or wiper noise.

08Where to go next

If the sound is a click, go to butt joint. If it is a rub, relubrication and dust protection cover the wiper side. If the axis is fast and the drag matters as much as the sound, friction and drive force has the numbers.

Silent series in the catalogue: QE low profile, QR roller, QW wide rail. For a general-purpose machine where noise is not the driver, HG series is the standard choice.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts