Beam first

Linear shaft selection: hardness, diameter, support spacing

A shaft rail is a beam that happens to be a bearing surface. It bends between its supports, and the bearing absorbs whatever deflection is left. Choosing the diameter from the bearing size alone is how a long axis ends up with a tight spot in the middle.

SF · SP · SI HRC 60–62 5 min read

01Three decisions, one shaft

  • Diameter sets the bending stiffness, the bearing size and the load capacity.
  • Hardness and finish set the wear life and the friction; the raceway is the surface, not the core.
  • Support spacing sets how much the shaft sags under its own weight and the load, which is often the real limit on a long stroke.

Most linear shaft problems on a long axis are the third item, not the first. A 20 mm shaft supported every 500 mm behaves better than a 30 mm shaft supported every 1,500 mm, and costs less.

02Materials and what the numbers mean

MaterialHardnessWhere it belongs
GCr15 / SUJ2 bearing steelHRC 60–62The standard raceway; induction hardened, ground and often hard chrome plated
9Cr18 / SUS440 stainlessHRC 55 and aboveWashdown, humidity, cleanroom and medical axes
Hard chrome on bearing steelCase dependentWear and corrosion protection where full stainless is not justified

The chrome layer is thin, typically a few micrometres to a few tens, and it protects the surface until it is worn or scratched. On a shaft that sees abrasive dust, the coating buys time but does not replace a wiper.

03Solid, hollow, inch

TypeConstructionTrade
SFSolid metric shaftMaximum stiffness, simplest end machining
SPHollow metric shaft70–80% of the bending stiffness at half the weight; bore can carry a rod or cable
SIInch shaftFor machines built to imperial dimensions; check the bearing bore, not just the diameter

Hollow shafts are the quiet fix for a moving gantry: the mass that has to accelerate falls, and the stiffness barely changes because the outer fibres do the work. The wall thickness and the end threads are the parts to confirm on the drawing.

04Deflection: the calculation that decides the spacing

For a shaft simply supported over a span L with a load at the centre, the sag is:

δ = F × L3 / (48 × E × I)
I = π × d4 / 64 (solid)
Guide keep δ under the bearing's allowable misalignment, typically a few hundredths of a millimetre

Two things follow. Deflection grows with the cube of the span, so doubling the support spacing multiplies the sag by eight; and it falls with the fourth power of the diameter, so one size up is worth more than one support more. Work out both before adding a bracket.

The shaft's own weight counts too. On a long horizontal axis with no load, the sag from self-weight alone can exceed the running clearance of the bearing.

05Matching the bearing and the housing

Linear bearings are made to a shaft tolerance band. The common pairing is a shaft ground to h6 and a housing bored to H7, with the bearing's internal clearance deciding the fit:

Bearing typeFit behaviourWhen to use
Adjustable clearanceCan be tightened after assemblyWhere a small preload is wanted and the housing is machined in place
Fixed clearanceSet by the bearing; no adjustmentStandard automation, interchangeable replacement
Flange or long versionSame bore, longer bodyCantilever loads and single-bearing supports

A shaft that is undersized for the bearing bore gives a rocking fit and a noisy axis; an oversized one will not enter. Measure the shaft at three positions along the stroke, not just at the end.

06Finish, storage and installation

  • Do not clamp on the raceway. Vise jaws and chuck marks become wear points. Hold the shaft on the end journals or on a soft jaw.
  • Keep it straight in storage. A shaft left leaning against a wall takes a permanent set over months; store it horizontally and supported.
  • Deburr the ends. A raised burr at the end scrapes the bearing seal on the first assembly and then keeps scraping.
  • Align the supports. Two supports at different heights preload the bearing in one direction over the whole stroke.

07Questions we get

Does a hollow shaft behave like a solid one?

In bending, almost: most of the stiffness sits in the outer fibres, so a hollow shaft of the same outside diameter is close to a solid one at half the weight. The wall and the end machining are the parts to check.

How straight does a shaft rail have to be?

Straight enough that the bearing does not absorb the error: a few hundredths over a metre for standard grade, tighter for precision. Support spacing matters more, because the shaft sags between supports.

Why is my shaft rusting under the bearing?

The bearing wipes the oil film away and traps moisture. Hard chrome delays it, stainless removes it. In washdown duty the shaft material has to match the guideway decision.

08Where to go next

All twenty guides are on the knowledge hub. The bearing that runs on this shaft is covered in linear bearing selection; the guideway alternative in cylindrical against square; the material decision in stainless guideways, and the drive force on friction and thrust.

Products: linear motion range. Send the stroke, the load and the support positions, and we will return the diameter and the support spacing.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts