SP Series Hollow Linear Shaft: Custom Bore, 12–60 mm OD

SP Series Hollow Linear Shaft: Custom Bore, 12–60 mm OD
+

Key Features

Hollow shaft with a custom bore, outside and bore ground in one set-up so the wall stays even at speed.

12–60 mmOutside diameter
CustomBore and wall
6000 mmMax length

Applications

Rotary shafts Lens tubes Coolant-fed spindles Test actuators Medical equipment Semiconductor handling

Linear Shafts · SP Series Hollow Linear Shaft: Custom Bore, 12–60 mm OD

Technical Description and Selection Reference

Product Overview

The SP series is the hollow counterpart of the SF shaft: same GCr15 steel, same case hardness, with a bore through the middle so the shaft can pass a rod, a cable, a coolant line or a second shaft. Wall thickness and bore diameter are machined to the customer drawing, which makes the series useful where weight matters as much as stiffness.

Outside diameters run from 12 mm to 60 mm with a matching bore, and the outside is held to h6 or g6. Because the wall is thinner than a solid shaft, the bending behaviour is different: a hollow shaft of the same outside diameter deflects more, and the selection guide gives the moment of inertia needed to compare it fairly with a solid shaft.

Typical uses are rotary shafts with a through bore, lens tubes, and axes where a fixed rod runs inside a moving sleeve. Ends can be threaded or flanged, and the bore can be keyed or stepped.

ParameterSpecification
SeriesSP hollow linear shaft, metric
Outside diameter12, 13, 16, 20, 25, 30, 35, 40, 50, 60 mm
BoreCustom inner diameter and wall thickness
MaterialGCr15 bearing steel (SUJ2)
HardnessHRC 60–62 on the outside
Case depth0.6–1.5 mm up to 15 mm OD; 0.8–2.0 mm 16–25 mm; 0.8–3.0 mm above 30 mm
Toleranceh6 or g6 outside, per size table
Maximum length6000 mm; longer by butted joint
ConcentricityBore and outside ground in one set-up
End machiningThread, flange, step, keyway
Minimum order1 piece
Lead time10–15 days, drawing required

Product Features

  • Bore and outside diameter are ground in one set-up, so the wall stays even and the shaft does not whip at speed.
  • Wall thickness is chosen from the load, not from stock: thin walls save weight, thick walls hold stiffness.
  • The through bore can carry a rod, a cable or a coolant line without a second shaft alongside.
  • Hardness and case depth follow the same specification as the solid SF series.
  • Bore ends can be chamfered, threaded or fitted with a flange for a bearing seat.

Applications

Where the bore also has to transmit torque, a ball spline does the job with a keyed race instead of a plain bore.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

Most adjustable and closed sleeves are specified against an h6 or g6 shaft. The choice follows the clearance class you want: g6 leaves a little more room and suits a free-running axis, h6 is tighter and suits a preloaded or precision axis. State the bearing part number when ordering Linear Shafts and the shaft tolerance is matched to it.

Case depth follows the diameter: 0.4–0.7 mm below 6 mm, 0.6–1.5 mm from 10 to 15 mm, 0.8–2.0 mm from 16 to 25 mm, and 0.8–3.0 mm above 30 mm. Hardness is HRC 60–62 through the case, with a soft core so the ends can be threaded without cracking.

A single ground shaft is available to 6000 mm. Beyond that, lengths are supplied as a butted joint with a dowel or threaded stud, with the joint face ground so it does not stand proud of the running surface. The joint should sit outside the loaded zone wherever the stroke allows.

Yes. Ends can be threaded, stepped, keyed, drilled or tapped, machined after hardening and before final grinding so the thread stays concentric with the running surface. Hard chrome is available for wash-down and humid service, and stainless grades are available on request.

Support spacing sets the deflection: a long unsupported span sags under the carriage load and the sleeve tightens mid-stroke. The shaft selection guide on this site gives the moment of inertia and the deflection formula, or send the load, span and diameter and our engineers will return the support layout.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Linear Shafts from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts