SI Series Inch Linear Shaft: 1/4 in Up, HRC 60–62

SI Series Inch Linear Shaft: 1/4 in Up, HRC 60–62
+

Key Features

Inch ladder shaft with imperial threads, so an imported machine keeps its original fits without reaming.

1/4 inMinimum size
HRC 60–62Hardness
UNC / UNFEnd threads

Applications

Imported machinery US-built packaging lines Retrofit axes Workshop fixtures Repair and spare parts

Linear Shafts · SI Series Inch Linear Shaft: 1/4 in Up, HRC 60–62

Technical Description and Selection Reference

Product Overview

The SI series covers inch shafts, ground to the same hardness as the metric range for machines built to imperial drawings. Sizes start at 6.35 mm (1/4 in) and follow the inch ladder, with the outside diameter toleranced in g6 or h6 as the drawing requires.

An inch shaft is not a converted metric shaft: the diameters, the bearing bores and the end threads all follow the inch series, so a mixed inch and metric machine keeps its original fits. Ends can be threaded UNC or UNF, stepped or keyed.

Stock lengths and cut-to-length supply both work; the same 6000 mm limit applies, with butted joints above it. Pair the shaft with an inch-bore linear bearing or a plain bushing, and check the fit against the linear bearing guide before ordering.

ParameterSpecification
SeriesSI inch linear shaft
Diameter range6.35 mm (1/4 in) upward, inch ladder
MaterialGCr15 bearing steel (SUJ2)
HardnessHRC 60–62
Case depth0.4–1.0 mm at small sizes, 0.8–2.0 mm above 3/4 in
Toleranceg6 or h6, per drawing
Maximum length6000 mm; longer by butted joint
SurfaceGround, hard chrome optional
End machiningUNC / UNF thread, step, keyway
Minimum order1 piece
Lead time7–10 days standard; 10–15 days with end machining

Product Features

  • Inch diameters and inch threads on the same part, so an imperial machine is not forced into metric fits.
  • Case depth is held to the smaller of the drawing requirement and the diameter rule, avoiding a through-hardened brittle shaft.
  • Cut-to-length or fixed stock lengths, both deburred and checked for straightness.
  • Optional hard chrome for wash-down and humid service.
  • Bearing bore and shaft tolerance are quoted together when the customer sends the bearing part number.

Applications

Replacing a worn inch shaft: send the drawing or the original part number, and the replacement is ground to the same tolerance band.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

Most adjustable and closed sleeves are specified against an h6 or g6 shaft. The choice follows the clearance class you want: g6 leaves a little more room and suits a free-running axis, h6 is tighter and suits a preloaded or precision axis. State the bearing part number when ordering Linear Shafts and the shaft tolerance is matched to it.

Case depth follows the diameter: 0.4–0.7 mm below 6 mm, 0.6–1.5 mm from 10 to 15 mm, 0.8–2.0 mm from 16 to 25 mm, and 0.8–3.0 mm above 30 mm. Hardness is HRC 60–62 through the case, with a soft core so the ends can be threaded without cracking.

A single ground shaft is available to 6000 mm. Beyond that, lengths are supplied as a butted joint with a dowel or threaded stud, with the joint face ground so it does not stand proud of the running surface. The joint should sit outside the loaded zone wherever the stroke allows.

Yes. Ends can be threaded, stepped, keyed, drilled or tapped, machined after hardening and before final grinding so the thread stays concentric with the running surface. Hard chrome is available for wash-down and humid service, and stainless grades are available on request.

Support spacing sets the deflection: a long unsupported span sags under the carriage load and the sleeve tightens mid-stroke. The shaft selection guide on this site gives the moment of inertia and the deflection formula, or send the load, span and diameter and our engineers will return the support layout.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Linear Shafts from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts