Two geometries

Cylindrical linear guides against square guideways

A cylindrical guide is a shaft with bearings riding on it; a square guideway is a profiled rail with a block wrapped around it. They solve the same problem with different structure, and the structure decides what each can carry.

SC · SBR · SGR vs HG · EG · WE 5 min read

01The structural difference

The shaft is a round beam; the bearing is a ring with balls inside. Load enters at one line of contact per row, and the ring is short, so the bearing has limited ability to resist a tilting moment. The rail is a profiled beam with raceways ground into it; the block wraps around the rail with two or four rows, and its length gives a moment arm.

Everything else follows: the shaft is cheap per metre and easy to cut; the rail is expensive and must be ordered in lengths and joints. The shaft needs two parallel rails to resist a moment; the rail can resist a moment on its own, which is why a single-rail axis exists in profiled guideways and almost never in shaft guides.

02Side-by-side comparison

CriterionCylindrical (shaft)Square (profiled rail)
Load per bearingModerate, limited by the ring lengthHigh; four rows share the load
Moment capacityLow on one shaft; needs a pair with spacingGood on a single rail; excellent as a pair
StiffnessShaft bending usually dominatesRail and block both stiff; preload raises it further
Long stroke costLow: shaft is cut to lengthHigher: rail in fixed lengths, joints need care
Alignment labourTwo rails must be made parallelOne rail is the datum; the second follows it
Dust and chipsBearings wipe less effectively; chips stick to oilWipers and metal scrapers available as standard options
RepairabilityShaft and bearing replaceable separatelyRail and block as a matched pair

03When the shaft wins

  • Long travel, light load. A 4 m shaft costs a fraction of a 4 m rail, and the deflection is manageable with intermediate supports.
  • Simple structure. A lift, a pusher or a sliding gate with two shafts and four bearings is the cheapest axis that works.
  • Harsh environment. There is no precision raceway to protect; a worn shaft is replaced, not re-ground.
  • Rotating use. A shaft can be the axis of rotation and the guide at the same time, which no profiled rail can do.

04When the rail wins

  • Any cantilever. A head hanging off the end of an axis generates a moment that a short bearing cannot take; the rail block can.
  • Precision positioning. Ground raceways and preload give repeatability that a shaft guide cannot reach.
  • Single-rail axes. A wide-rail or a heavy-load rail replaces two shafts and the structure that held them.
  • Machine tools and cutting. Stiffness under load and chip protection are the two reasons.

The moment arithmetic is the same for both, and it is on moment load: M = F × l, compared with the permissible moment of the bearing or block.

05The families on each side

FamilyStructureUse
SC / SCEShaft with a block bearing, V or S profileGeneral automation, short strokes
SK / SHFCompact shaft bearing unitsSmall fixtures, light heads
KBEOpen-type bearing, shaft supported at the endsWhere the shaft must pass through
SBR / TBRTwo shafts in one aluminium profileHeavy transfer, gantry beams
SGR / SGBRoller bearing on a profiled shaftLong stroke with heavier load, quieter than ball
OSG / OSGBShaft guide with side blocksWhere a side load is present

06The cost that quotes leave out

The shaft looks cheaper on paper and sometimes is. The difference appears in assembly: two shafts have to be made parallel within a few hundredths over the full stroke, and the bearings have no adjustment for that error. A profiled rail is aligned once and the second rail follows it, which saves hours on a long axis.

Add the guard, the wiper and the second rail, and the gap narrows. For a cantilevered or precision axis it reverses, and the rail is the cheaper answer once the structure is counted.

07Questions we get

Is a cylindrical guide cheaper for the same load?

Often on a long, lightly loaded axis, because the shaft is a commodity. It stops being cheaper when the axis needs moment capacity, because the fix is a second rail and a wider spacing.

Can a cylindrical guide hold a cantilevered load?

Only with a long bearing or two bearings spaced apart. A single short bearing on a shaft has little moment capacity, and the shaft itself bends.

Why do cylindrical guides need more alignment work?

Two separate rails must be parallel in both planes and the bearings absorb little error. A profiled rail carries its own datum faces, so one rail is aligned and the other follows.

08Where to go next

All twenty guides are on the knowledge hub. The moment case is on moment load; the shaft side is on linear shaft selection; the bearing side on linear bearing selection; the rail families on series comparison, and the sizing arithmetic on the load and life calculator.

Products: linear guideways. Send the stroke, the head offset and the load, and we will say which geometry the moment allows.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts