SC Series Cylindrical Guide: 8–50 mm Shaft, Aluminium Block

SC Series Cylindrical Guide: 8–50 mm Shaft, Aluminium Block
+

Key Features

Aluminium carriage on a hardened shaft, offered in three body lengths for short-stroke axes.

8–50 mmShaft diameter
3Body lengths
1,570 NMax dynamic (SC30)

Applications

Pick-and-place heads Cutting and trimming Label applicators Test fixtures Small gantries Door actuators

Cylindrical Guides · SC Series Cylindrical Guide: 8–50 mm Shaft, Aluminium Block

Technical Description and Selection Reference

Product Overview

The SC series is the light cylindrical guide: an aluminium carriage with a lined bore runs on a hardened shaft, and the carriage carries the load through a plain or rolling interface depending on the model. It is the cheapest way to build a short-stroke linear axis with moderate accuracy.

Shaft diameters run from 8 mm to 50 mm, and each size is offered with a short, standard or long carriage. Long carriages spread the load over more shaft and take more moment, which is the usual fix when a short carriage rocks at the end of the stroke.

The carriage is aluminium with sealed ends, so chips and coolant stay out of the bore. Mounting bolts go through the carriage top or the side flange. For a shaft that is supported only at the ends, check the deflection: the shaft guide gives the support spacing calculation, and the round-to-profile comparison explains where this family stops being the right answer.

ParameterSpecification
SeriesSC cylindrical linear guide
Shaft diameter8, 10, 12, 13, 16, 20, 25, 30, 35, 40, 50 mm
CarriageAluminium, short / standard / long
SealsUU double seal standard
Dynamic load (reference)From about 270 N at SC8 to about 1,570 N at SC30
Static load (reference)From about 390 N at SC8 to about 1,570 N at SC30
Mounting boltsM4 to M8, per size
Shaft toleranceh6 or g6
StrokeSet by shaft length and support spacing
Operating temperatureConfirmed at quotation for the selected seal compound
Minimum order1 piece
Lead time3–7 days for stock sizes; 10–15 days custom

Product Features

  • Aluminium carriage keeps moving mass low, which matters on a fast pick-and-place head.
  • Three carriage lengths per size: the long body is the cheap fix for rocking at stroke ends.
  • Sealed ends and a lined bore tolerate dust better than an open sleeve.
  • Bolts come through the top or the side, so the carriage fits either a plate or a bracket.
  • Load figures are quoted per size, not as a single headline number, because the range spans a factor of five.

Applications

Short stroke, moderate load and a tight budget: this is the family to start from. Heavy side load or a long cantilever moves the choice to a profile rail.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

A round shaft axis is the lower-cost choice for short stroke, moderate load and a simple frame. A profile rail wins once the carriage sees a real moment, the stroke is long, or the accuracy has to hold under side load. The comparison page on this site sets out the crossover.

SC is a single shaft with an aluminium carriage, the simplest and cheapest axis. SBR and TBR put two shafts in one block, which resists roll without a second rail to align. KBE is an open block for a shaft that is supported along its length, used where the shaft has to pass a support rail.

The long carriage spreads the load over more shaft and takes more moment, which is the usual fix when a short block rocks at the end of the stroke. If the load is centred and the stroke is short, the standard body is enough. Tell us the overhang and the load position and we will size the body.

Yes. The standard build uses UU double seals, and PP seals are available on the twin-rail family. For fine dust or coolant mist, add a bellows cover: a seal keeps chips out of the bore but it does not stop a build-up on the shaft.

Yes. Cylindrical Guides is supplied as a matched set on request, with the shaft lengths cut to your stroke and the end supports drilled to the same centre distance. That removes the alignment step on the machine frame.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Cylindrical Guides from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts