SBR/TBR Twin-Rail Cylindrical Guide: 10–50 mm, Matched Set

SBR/TBR Twin-Rail Cylindrical Guide: 10–50 mm, Matched Set
+

Key Features

Two shafts in one aluminium block, so the carriage resists roll without a second rail to align.

10–50 mmShaft diameter
2,360 NMax dynamic (SBR16L)
Matched setWith end supports

Applications

Gantry axes Transfer units Cutting tables Woodworking Packaging machines Roller conveyors

Cylindrical Guides · SBR/TBR Twin-Rail Cylindrical Guide: 10–50 mm, Matched Set

Technical Description and Selection Reference

Product Overview

The SBR and TBR families are twin-rail cylindrical guides: two hardened shafts run parallel in one aluminium block, and the carriage bridges both. The pair shares the load, so the carriage resists roll far better than a single shaft of the same diameter, and the block can be bolted straight to a plate without a second rail to align.

SBR covers the standard duty sizes from 10 mm to 50 mm shafts, with standard and long carriages and PP seals. TBR is the heavier build for gantry and transfer axes where the carriage also sees a moment. Both are supplied as a matched set: block, shafts and end supports, so the centre distance is fixed before the parts leave.

Because the two shafts are in one block, the assembly is self-aligning to the plate, and the mounting height is lower than two separate rails of the same size. For a cantilever, that lower height matters more than the load rating: the moment guide shows why.

ParameterSpecification
SeriesSBR / TBR twin-rail cylindrical guide
Shaft diameter10 to 50 mm
CarriageAluminium block, standard or long, PP seals
ConfigurationTwo shafts in one block, matched set with end supports
Dynamic load (reference)About 1,020 N at SBR10L to about 2,360 N at SBR16L; TBR higher
Static load (reference)Quoted per size in the datasheet
MountingBlock bolted to plate; shafts fixed at both ends
Shaft toleranceh6 or g6
StrokeSet by shaft length and support spacing
AlignmentFixed by the block, no second rail to align
Minimum order1 set
Lead time7–10 days; 10–15 days custom length

Product Features

  • Two shafts in one block resist roll without a second rail to align, which cuts assembly time on a gantry.
  • Lower mounting height than two separate rails, so the centre of gravity stays down.
  • Matched set supplied with shafts and end supports, keeping the centre distance fixed.
  • Long carriages take the moment that a short block cannot.
  • PP seals and a lined bore handle dust in transfer and packaging lines.

Applications

Where the axis has to carry a moment and the budget rules out a profile rail, this is the compromise that keeps the frame simple.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

A round shaft axis is the lower-cost choice for short stroke, moderate load and a simple frame. A profile rail wins once the carriage sees a real moment, the stroke is long, or the accuracy has to hold under side load. The comparison page on this site sets out the crossover.

SC is a single shaft with an aluminium carriage, the simplest and cheapest axis. SBR and TBR put two shafts in one block, which resists roll without a second rail to align. KBE is an open block for a shaft that is supported along its length, used where the shaft has to pass a support rail.

The long carriage spreads the load over more shaft and takes more moment, which is the usual fix when a short block rocks at the end of the stroke. If the load is centred and the stroke is short, the standard body is enough. Tell us the overhang and the load position and we will size the body.

Yes. The standard build uses UU double seals, and PP seals are available on the twin-rail family. For fine dust or coolant mist, add a bellows cover: a seal keeps chips out of the bore but it does not stop a build-up on the shaft.

Yes. Cylindrical Guides is supplied as a matched set on request, with the shaft lengths cut to your stroke and the end supports drilled to the same centre distance. That removes the alignment step on the machine frame.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Cylindrical Guides from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts