Full index

Every guide in one place

The MS Linear product selection library — thirty-five pages selected from our selection catalogues, datasheets and engineering application notes: sizing and life, installation and protection, special formats, and the screws, modules, shafts and bearings that sit around a rail. Each entry is one question, answered once. For the full selection PDF and complete part-number tables, contact MS Linear.

38 entries 6 groups Product pages linked from every guide

01Start here

Linear guideway sizing guideNine steps from load case to part number, in the order the checks actually happen.Sizing
Load and life calculatorEnter load, speed and size; returns static safety and rating life in hours.Tool
Size chart and ratingsStatic and dynamic ratings for size 15 to 65, ball and roller, with the smallest size for a given load.Data
Accuracy and preloadC, H, P, SP, UP and Z0, ZA, ZB: what each grade promises and where the pairs stop matching.Grade
Ball against rollerContact geometry, the rating-base trap, and the four signals that favour rollers.Compare
Guideway FAQTwenty-nine short answers to the questions that arrive before a quotation.FAQ

02Load and life

Moment loadMR, MP, MY, the overhang formula and the four ways to lower a moment before changing size.Load
Mean loadWhy a peak load is the wrong input for life, and the three equivalent-load formulas.Load
Life correctionHardness, temperature and load factors, and what each one does to the hours.Life

03Running the axis

Friction and thrustThree resistance sources, the three mounting attitudes, and the drive force behind a motor choice.Drive
Lubrication and relubricationGrease against oil at 60 m/min, the 100 km interval and how to turn it into hours.Maintenance
Installation sequenceMaster rail, four clamping methods, seven steps, and the four ways to align without a side push.Assembly
Butt jointsWhen a rail must be joined, where the joint goes, and why the pair has to be staggered.Assembly
Mounting surfaceFlatness and parallelism tolerances by grade, four measurement methods, four remedies.Assembly
Mounting orientationHorizontal, side-mounted, inverted and vertical: where gravity lands and what changes with it.Assembly
Dust protectionStandard, ZZ, KK and DD wiper combinations, matched to chips, coolant and fine powder.Protection
Guideway noiseFour sound sources, a frequency estimate, and the order to diagnose them in.Diagnosis
Series comparisonAll guideway families on four axes, the five-step choice order and the five mis-selections.Compare
Replacement cross-referenceMap a drawing designation to the right family, then the four dimensional checks before a swap.Replacement

04Special formats

Miniature guidewaysSize 7 to 15: moment dominance, M2 to M4 screw torque, dust-sheet clearance and rail end distance.Small
Wide rail guidewaysOne track replacing two rails, the mounting height it costs, and where length becomes the limit.Single rail
Stainless steel guideways9Cr18 at HRC 55 against GCr15 at HRC 60-62, plus the corrosion cases it does not solve.Material
Silent guideway selectionFour noise sources, three the block controls, and the checks before paying for a quiet series.Acoustics
Locking guidewaysClamping the carriage instead of the screw, and when a motor brake is the better device.Holding
TGH against TGLIdentical C and C0 on a shared rail; the difference is 4 to 10 mm of carriage height.Compare
CA against HALong carriage: 22 percent more C and 33 percent more C0, paid for in stroke and plate holes.Compare
DG against TGLow-profile band from 24 to 42 mm, the matched carriage and rail set, and where TG takes over.Compare

05Screw, module and support

Ball screw part numbersNine segments from thread direction to preload, with the circulation letters and grade pairing.Screw
Linear module selectionFour inputs, standard rail lengths, critical speed and the moment check at the end of travel.Module
Support seatsFixed and supported ends, the four families, and the bearing clearance behind each grade.Support
Combined transmission blocksScrew support and motor pilot in one housing, and what that commits the design to.Integrated

06Shafts and bearings

Linear shaft selectionHardness, hollow sections and the deflection rule that sets support spacing before diameter.Shaft
Cylindrical against squareThe structural difference, the moment case that rules a shaft out, and the alignment labour.Compare
Heavy cylindrical guidesTwin-shaft profiles, roller rails and the 6 m line where docking starts.Heavy
Linear bearing selectionAdjustable against fixed clearance, long bodies, and the h6 / H7 fit behind the rattle.Bearing
Flanged linear bearingsSquare and round flanges, body length as moment capacity, and plate rules that stop tilting.Bearing

07Buying and delivery

How an order runsDrawing review, quotation, production, inspection, packing and delivery, and what the quote fixes.Buying
RFQ checklistThe eight fields that set the price, where the markings are, and a copy-ready enquiry template.Buying

Browse by product line

The same pages, grouped as cards: knowledge hub. Products they refer to: linear guideways, ball screws, single-axis robots.

Send a load case

Ratings and dimensions quoted in these pages are reference values for selection. The shipping inspection sheet and the drawing govern the delivered part.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts