01One rail, two carriage lengths
CA and HA are the same family, the same rail and the same ball rows. The difference is how much carriage body sits on either side of the ball rows, which is why the two blocks are usually printed as two rows of one table with a shared rail column.
A short block is the default in most drawings because it takes less room and costs less. A long block exists for one reason: to spread the same load over more balls and to move the load reaction further from the mounting face, which raises both the load rating and the moment capacity. Everything else about the block, including the rail, stays the same.
02What the long block adds
The numbers below are the CA and HA rows from our catalogue for the standard-height family. They are reference values for selection; the drawing for the ordered part governs.
| Size | L, CA | L, HA | Extra length | C, CA → HA | C0, CA → HA |
|---|---|---|---|---|---|
| 20 | 50.5 | 65.2 | 14.7 | 17.75 → 21.18 | 37.84 → 48.84 |
| 25 | 58 | 78.6 | 20.6 | 26.48 → 32.75 | 56.19 → 76.00 |
| 30 | 70 | 93 | 23 | 38.74 → 47.27 | 83.06 → 110.13 |
| 35 | 80 | 105.8 | 25.8 | 49.52 → 60.21 | 102.87 → 136.31 |
| 45 | 97 | 128.8 | 31.8 | 77.57 → 94.54 | 155.93 → 207.12 |
| 55 | 117.7 | 155.8 | 38.1 | 114.44 → 139.35 | 227.81 → 301.20 |
The pattern is consistent: about 22 percent more dynamic rating, about 33 percent more static rating, and 15 to 38 mm of extra carriage length. The static gain is larger than the dynamic gain because the longer block adds ball rows in contact at the ends, which is where a static overload shows first. The three static torques rise by roughly a third as well, since the reacting couple grows with the length.
Size 15 is listed as CA only in the standard-height table. If a 15 rail has to carry a moment, the usual route is a longer block from a different family or a second rail, not a longer 15 block.
03Stroke is what you pay
A carriage occupies rail length. When the block grows by 23 mm at size 30, the rail has to grow by the same amount to keep the same travel, or the travel shrinks by 23 mm on a fixed rail. On a machine where the rail length is already set by the bed, that 23 mm comes straight out of the stroke.
- Two blocks per rail. Both grow, so the space between them has to grow as well if you keep the same support base. In practice the pair takes 46 mm more rail at size 30.
- End stops and bumpers. A longer block reaches the end stop earlier. Check the end distance in the drawing before assuming the old guard still fits.
- Bellows and covers. The compressed length of a bellows is set by the block envelope, not the rail.
The comparison is therefore not "more capacity for the same axis" but "more capacity for less travel". On a short-stroke press or a compact slide, that trade is usually the wrong way round: a bigger size in a short block often gives the same rating without eating stroke.
04Load per block, not just rating
A rating only helps if the load per block actually falls. Two effects run at once when the block is lengthened.
First, the load is shared over more ball rows, which is what the higher C represents. Second, the load distribution across a four-block table changes: a long block resists a pitch or yaw moment with a longer couple, so the corner blocks of the table see a smaller peak. On a table whose centre of gravity sits outside the block rectangle, that second effect is often worth more than the rating increase.
Run the numbers rather than the ratios. Enter the table load, the block spacing and the offset in the load and life calculator; it returns the worst-loaded block and the life that follows. If the worst block is already below half its C, the long block is not the lever you need.
05Deflection and preload
The long block also changes how the carriage behaves under a reversing moment. The ball rows at the ends of a long carriage sit further apart, so the same angular deflection requires more ball compression, which raises the effective stiffness. That is why a long block in ZA preload can feel stiffer than a short block in ZB, even though the short block has the higher preload grade.
Where the axis has to hold position under a changing load, this matters more than the rating columns. Where the axis runs in one direction under a steady load, it does not, and the extra length is dead weight.
Preload itself is a separate decision: accuracy grade and preload covers Z0, ZA and ZB and what each does to life.
06When HA is the right call
- The moment runs out before the load. Long tooling, an offset centre of gravity, or a single-rail gantry where roll is the limiting check.
- You cannot add a second rail. When the machine envelope fixes the rail count, the only way to raise the moment capacity is a longer block.
- Shock loads. The static rating gain of a third is the cheapest way to lift the safety factor without moving up a size.
- Thin plates. A long block spreads the fixing load over a longer plate area, which helps where the moving plate is thin or drilled close to the edge.
07When CA is enough
- Short stroke. Where every millimetre of travel is contested, the short block wins by default.
- Four blocks on a wide table. The block rectangle already spreads the moment; the long block adds little.
- Light, fast axes. Moving mass dominates settling time; the shorter, lighter block is the better trade.
- Cost-driven builds. Same rail, less material, shorter plate, lower price and shorter lead time.
A useful default: start with CA, run the worst-block load and the moment check, and only move to HA when one of them fails. Moving up a size is the other option, and it usually costs more height than the long block costs stroke.
08The plate has to change with it
The rail hole pattern is shared, but the carriage fixing holes are not. A long block has its mounting holes further apart, so the moving plate drilled for a CA block will not accept an HA block without new holes. On a retrofit, that means a new plate or a transfer plate, and the height of that plate enters the stack.
Two checks before the drawing is released: the carriage hole pitch in the block table, and the distance from the carriage face to the ball rows, because both change with the block length. Both are printed in the same row as L and C.
09Where to go next
If the carriage length is settled but the family is not, TGH against TGL covers the height decision on the same rail. The rating for every size is in the size chart, and the family map is in the series comparison.
The moment check behind the HA decision is in moment load; the stroke and rail length arithmetic is in the selection guide. All guideway families sit under linear guideways.
Send the stroke, the rail length and the block count through the inquiry form and we reply with the block type, the rail length that keeps the travel, and the plate hole pattern.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
