Reference
Accuracy grades and preload on a linear guideway
Two separate choices decide how a guideway behaves: the accuracy grade sets how straight the carriage runs, and the preload sets how stiff it feels. Buyers mix them up constantly, and the mistake shows up as chatter, binding or a bill for a grade that the frame could never hold.
01What the grade actually controls
An accuracy grade is a statement about three measurements, not about the machining quality of the rail as a whole:
- Running parallelism. How far the top of the carriage deviates from a straight reference while it travels the length of the rail. This is the number that decides whether a dial gauge stays still.
- Height and width tolerance of the block. How close the block sits to its nominal height, which matters when two rails share one gantry and the load must split evenly.
- Pair matching. For two-rail axes, how closely the two rails and their blocks match each other, so the moving table does not tilt as it crosses the working area.
The five grades in common use step through those three measurements together. Each step costs more because more rails are rejected or reworked during inspection, not because more material is used.
| Grade | What it is for | Where it stops being enough |
|---|---|---|
| C normal | Transfer axes, pick-and-place, packaging, warehouse gantries. Position is usually closed by a sensor or a servo, not by the rail. | Any axis that interpolates a contour or holds a dimension by rail geometry alone. |
| H high | General automation, assembly gantries, printing and labelling, light machining with feedback. | Long travels where the error accumulates past what the control loop can absorb. |
| P precision | CNC positioning axes, grinding and EDM fixtures, laser cutting beds. | When the bed itself is not flat enough to let the rail perform at P. |
| SP super precision | High-end machining centres, measuring machines, optical stages. | Axes that still vibrate because preload or mounting, not grade, is the problem. |
| UP ultra precision | Semiconductor handling, metrology, precision optics, wafer inspection. | Any environment where temperature swing exceeds the tolerance band you are buying. |
Nominal numbers are not the promise. The tolerance values for each grade come on the inspection sheet for the rails you receive. We quote the grade and ship the measured values with the rail, so you are comparing real numbers rather than a catalogue class.
02What preload changes
Preload is the internal force already sitting between the balls or rollers and the raceway before any external load arrives. It is created by making the block slightly wider than the gap it runs in, so the rolling elements are compressed from both sides.
The effect is stiffness. A preloaded block does not rock when the load reverses direction, which is what removes the dead band at the start of a cut or a move. The cost is friction, heat and a shorter rating life at the same external load.
| Preload | Behaviour | Typical use |
|---|---|---|
| Clearance Z0, no preload | Lowest friction, a small amount of play under reversing load. | Vertical axes, gravity-loaded transfer, low-speed handling where smoothness matters more than stiffness. |
| Light ZA class | Play removed, little added friction, moderate rigidity. | The default for most automation, packaging, pick-and-place and light machining. |
| Medium ZB class | Noticeably stiffer, higher friction, more heat at speed. | Cutting axes, heavy gantries, side-loaded heads, presses. |
| Heavy on request | Maximum rigidity, highest friction and internal load. | Slow, heavily loaded axes where deflection is the limiting factor and speed is not. |
Preload is also where the life calculation gets less obvious. The internal preload force sits on the raceway all the time, so the load used for the L10 calculation is higher than the external load alone. That is why a medium-preload axis can show a shorter calculated life than the same rail run with light preload, at the same working load. The size calculator takes the external load; add preload when you compare against a datasheet rating.
03The pairing that actually works
Grade and preload are independent, and the useful combinations are narrower than the catalogue suggests. Four pairings cover almost every machine we quote:
| Machine | Grade | Preload | Reason |
|---|---|---|---|
| Transfer, loading, packaging | C or H | Light | Position is sensor-driven; stiffness only has to stop the block rocking. |
| Assembly gantry, dispensing | H | Light | Needs repeatability at moderate speed without heat build-up. |
| CNC positioning, grinding | P | Medium | Cutting force pushes the block sideways; the preload has to carry it without deflection. |
| Measuring, wafer, optics | SP or UP | Light | The rail must be straight, but heavy preload would add heat and shorten life in a temperature-controlled room. |
The mistake we see most often is paying for SP and then mounting it on an unmachined frame. A rail can only run as straight as the surface under it. Check the mounting pad flatness, the parallelism of the two rail seats and the stiffness of the frame before the grade is chosen; if those are out, the extra grade is invisible in the finished machine.
Rule of thumb. Fix the frame first, then the preload, then the grade. Preload decides whether the axis feels solid; grade decides whether it stays on line over a metre.
04How to write it on an RFQ
A guideway inquiry without grade and preload gets a standard-grade quotation, and the difference surfaces after the order. One line fixes that:
Grade P
Preload ZA light
Rail 2 pcs, 1200 mm, cut square, no joints
Blocks 4 pcs, flange type
Checks inspection sheet with measured running parallelism
Series and size
Ball or roller, and the size class from the load calculation. If the size is still open, run the numbers first so the grade is not chosen for a rail that is too small.
Grade and preload
Both, every time. A grade without preload leaves the stiffness to chance.
Rail length and joint policy
Long rails arrive joined; a joint sits inside the travel and shows up as a step. Say whether joints are allowed and where they may fall.
Inspection sheet
Ask for the measured parallelism and block height values, not just the grade label. That is the document you can check on receipt.
05Checking it on receipt
Three checks catch almost every grade or preload problem before the machine is built:
- Running parallelism. Mount a dial gauge on the carriage, sweep the full rail length, and compare the reading against the value on the inspection sheet. A step at the joint means the rails were joined in the travel zone.
- Block height across a pair. With two rails set side by side on a surface plate, measure both blocks at the same station. A mismatch that exceeds the pair tolerance tilts the table.
- Play under reversal. Push the block by hand, or with a gauge, in both directions. Movement before resistance means the preload is lower than specified, or the block was assembled with clearance.
If the measured values and the sheet disagree, stop before assembly. Reworking a frame around a rail that is out of tolerance costs far more than replacing the rail.
06Questions we get
Does a higher accuracy grade increase load capacity?
No. The grade limits geometry; the ratings come from the raceway and the rolling elements. A P-grade rail carries the same load as a C-grade rail of the same size.
Can I use a precision rail on a welded frame?
You can, but the frame error is added on top of the rail error and usually dominates it. Machine the mounting pads and check flatness first.
Which preload for a vertical axis?
Light preload in most cases, because the axis reverses and the block would otherwise rock. A pure gravity-loaded lift with no side load can run Z0 clearance.
Does preload change the life calculation?
Yes. Preload is a permanent internal load, so it belongs in the load used for L10. Comparing a medium-preload axis against a light-preload datasheet figure understates the load.
Do grade and preload change lead time?
They can. Standard grade and preload move quickly; matched pairs and measured inspection sheets take longer because every rail is checked and paired. Put both on the RFQ so the date quoted matches the part you need.
07Where to go next
If the size is still open, size it first: the guideway size calculator returns the load per carriage and the required C. The selection guide covers the series map, rail length and lubrication. Preload also raises the internal load that the life calculation has to carry: the corrected life page shows how much a ZB block costs against a ZA one. When the grade and preload are set, send them with the drawing and we quote against the actual part.
Ball rails in the sizes discussed here: HG series, EG low profile. Roller rails for cutting axes: RG series. If the type is still open, start with ball or roller guideway and settle the contact geometry before the grade. Preload also raises drag: the drive-force consequence is worked through in friction and drive force, and a heavily preloaded block uses up its grease film sooner, so the relubrication interval has to be shortened with it.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
