01The four axes behind every series name
| Axis | What it changes | Typical options |
|---|---|---|
| Contact type | Load capacity, rigidity, friction, noise | Ball, roller, cross roller |
| Mounting height | Centre of gravity, moment on the block | Standard, low profile, miniature |
| Rail width | Roll stiffness on a single rail line | Narrow, standard, wide |
| Protection | Life in chips, coolant and dust | Wiper codes, metal end caps, covered rail |
Two series that look similar in a photo can differ on only one of these axes, and that one difference is usually the reason the application needs it. Reading the catalogue by axis is faster than comparing model codes.
02The families, grouped by what they solve
Seventeen product families reduce to six jobs. The links below are to the series pages, not to a size chart:
General machining and four-direction load
HG series is the standard four-row ball rail: equal capacity in all four directions and enough self-alignment for a bed that is milled rather than ground. Where the same envelope has to carry more, QH adds balls in contact and a stiffer block without changing the mounting height.
Low profile and high speed
EG lowers the table towards the bed, which cuts the moment before any calculation is needed. QE keeps that height and changes the ball return for quieter running, and SE keeps the low envelope but adds metal end caps for hot chips.
One rail doing the work of two
WE and QW widen the rail so a single line resists roll. They suit cantilevered heads, gantry axes with no room for a second rail, and machines where bed width is the constraint. CG is the same idea taken further: an anti-torque block that will not rotate under an offset load.
Heavy load and shock
RG is the roller baseline: more rigid, more shock capacity, and a different life base. QR quietens it, and UR is the size class for press frames and lifting axes.
Precision and metrology
PG is built for tight height and parallelism control under measuring and wafer stages. AG uses cross-roller contact where the axis has to resist moment in every direction at low speed.
Environment and maintenance
CRG covers the raceway against chips. E2 and EL carry a lubricant reservoir for lines that are hard to service. Stainless covers washdown, and MG covers the small end: lab equipment, 3D printers, pick-and-place heads.
03Choosing in the right order
Load and moment first
Four-direction load, single-rail roll or heavy shock. This decides ball, roller, wide or anti-torque before anything else.
Then the mounting height
If the table has to sit low, the low-profile families are the only candidates, and the load capacity is what you accept in exchange.
Then the bed width
Two rails need spacing for a pair; a single wide rail needs bed width but no second datum. Whichever the frame allows decides the family.
Then accuracy and preload
The grade applies across families, so it narrows the choice last. Grades and preload explains what each one costs.
Then the environment
Sealing and lubrication can often be added to an existing family as a code, which is cheaper than changing family for protection alone.
04Five mis-selections we see
| What was specified | What was actually needed |
|---|---|
| Roller everywhere, "for rigidity" | A ball rail that is fast enough for the cycle. Rollers add drag, noise and cost where the cut does not need them. |
| Wide rail to avoid a second rail | Two rails, where the frame had the width. A wide rail saves assembly, not stiffness. |
| Low profile for a tall gantry | Standard height with a wider rail spacing; the low block reduces capacity without fixing the moment. |
| Heavy sealing on a clean axis | Wiper inspection. DD-class sealing on a clean high-speed axis adds heat and drag for nothing. |
| Higher accuracy grade to fix a rough bed | Bed correction. The rail follows the bed; the grade only decides how precisely it does so. |
05Questions we get
Is a wide rail always better than two narrow rails?
No. It resists roll on one line and saves bed width, but cannot match the stiffness of two rails spaced further apart.
Why use a low-profile series instead of a standard one?
Height, not load. The lower block reduces the moment on the blocks, at the cost of capacity for the same rail width.
When is a silent series worth the extra cost?
When operators share the space or noise is in the acceptance spec. It changes the ball return, not the load rating or grade.
06Where to go next
Once the family is shortlisted, size it with the calculator and confirm the sequence in the selection guide. If the choice is between ball and roller, ball vs roller settles it on life base and rigidity rather than on the catalogue photo. Where the machine has to be quiet, noise explains what the silent families change and what they cannot fix. Single-rail layouts that cannot be widened are covered in moment load.
Browse the whole range under linear guideways, or send the load case through the inquiry form and we will shortlist the family with the datasheet.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
