Machine bed

Guideway mounting surface: flatness, parallelism and how to measure it

A rail is bolted to the bed and follows it. Whatever the bed does over the stroke, the carriage does too, and no grade on the rail can correct it. This page covers what the bed has to deliver and how to prove it.

Flatness Two-rail parallelism 5 min read

01Two errors, two consequences

The mounting face contributes two independent errors, and they fail differently:

  • Flatness along the rail. A dip or a hump under the rail makes it bend. The blocks then travel on a curved path, and the carriage pitches as it crosses the error. On a precision machine this appears as straightness error in the finished part.
  • Parallelism between the two rails. Rails that converge or diverge preload the blocks against each other. The table runs tight in one zone, the drive current rises, and one rail runs hotter than the other.

The two are measured separately and fixed separately. A bed can be flat and still have non-parallel rails, and a perfectly parallel pair can sit on a bowed surface.

02Figures that go with each grade

The rail catalogue gives the parallelism of the rail itself; the bed requirement is derived from it and from the machine's accuracy target. In field practice the numbers land in this range:

GradeTypical bed flatnessPractical note
C / HTens of micrometres per 500 mmGeneral machinery; a planed or milled bed is usually enough.
PAround 5–10 µm per 500 mmGrinding or precision planing; the bed has to be measured, not assumed.
SP / UPA few micrometres per 500 mmScraped or ground and inspected with a granite reference; the installation itself becomes a measurement job.

These are starting points for the specification, not a substitute for the catalogue. Confirm the figure for the exact series and grade before the bed is machined, because correcting a bed after the fact costs more than machining it correctly the first time.

03Measuring the bed

1

Straight edge and feeler

A granite or ground straight edge laid along the rail line, with a feeler gauge at intervals. Quick, and enough to find a dip of tens of micrometres.

2

Dial indicator on a bridge

A bridge carried on the first rail, with an indicator reading the second rail face. This gives parallelism along the stroke, which is the number that matters for running force.

3

Laser or autocollimator

For SP and UP work, where the reading has to resolve a few micrometres over metres. Slower to set up and the only practical way to certify the bed.

4

Record the stations

Measure at fixed intervals and write the numbers down. A single maximum figure hides whether the error is a step, a bow or a twist, and each of those has a different remedy.

04When the bed is out of tolerance

ErrorRemedyLimits
Local dip or stepRe-machine or scrape the face, then re-measure.Needs the bed to be accessible; welding repairs distort the surrounding area.
Overall bow over a long bedMachine the face in one setup with the bed supported as it will be in service.Supporting the bed differently in the machine shop and on site reintroduces the error.
Moderate wear, no room to machineMachined epoxy layer, cured and then planed or ground.Not for heavy impact or high-temperature beds; thickness has to be controlled.
Rails not parallel, bed acceptableAdjust the subsidiary rail with a bridge indicator; do not compensate with preload.Preload hides the symptom and adds drag and heat.

Do not compensate with a higher grade. Fitting an SP rail to a bed that is out of flatness gives a rail that follows the bed error more precisely. The machine's accuracy is set by the bed, and the grade only decides how much of the bed error the rail adds to it.

05What this means for the specification

Two sentences in a purchase order decide whether the installation works: the flatness of the mounting face, and the parallelism between the rails, both quoted per unit length and over the full stroke. Without them, the rail supplier can only guarantee the rail, and the machine builder is left to discover the rest at commissioning.

The bed requirement should be written before the rail grade is chosen. Choosing the grade first and then discovering that the bed cannot support it is the usual reason a precision machine ends up running at general-purpose accuracy.

06Questions we get

Can a precision rail compensate for a bad bed?

No. The rail takes the shape of the surface it is bolted to; a higher grade follows the error more accurately rather than correcting it.

How flat does the mounting face need to be?

It scales with grade and rail length: P and SP beds are usually specified in the order of 5 to 10 µm per 500 mm, C and H allow more. Confirm with the catalogue for the series.

Is epoxy a legitimate way to correct a bed?

For moderate errors and moderate temperatures, a machined epoxy layer is a standard repair. It is not suitable for deep wear or heavy impact, and needs planing or grinding after curing.

07Where to go next

The measurement sequence continues in installing a guideway, where the bed tolerance becomes the rail alignment procedure. Accuracy grades and preload explains what the rail itself contributes, and rail joints covers the long beds where a joint and a bed error meet.

Precision rails for scraped beds: PG series, AG cross roller. General machinery: HG series.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts