01Two checks, two different loads
A guideway sees at least two loads in any real cycle, and they answer different questions:
- The peak load decides the static check: fSL = C0 / P and the moment check against M0. A rail that is undersized here brinells the raceway on the first hard stop, regardless of how long the machine runs.
- The mean load decides the life figure: L = (C / Pm)3 × 50 km. A rail that is undersized here runs for a year and then fails in service.
Because the life equation is a power function, the mean is not an arithmetic average. It is an average weighted towards the heavy parts of the cycle, which is why a short heavy cut matters more than a long light pass.
02Three formulas, one idea
All three expressions below are the same weighted average written for a different shape of duty cycle. The exponent n is 3 for a ball guideway and 10/3 for a roller:
| Duty cycle | Mean load | Use when |
|---|---|---|
| Stepped | Pm = [ (P1nL1 + P2nL2 + … ) / L ]1/n | Distinct phases with a known load and a known length or time for each. |
| Linearly varying | Pm = (Pmin + 2Pmax) / 3 | The load ramps from one end of the stroke to the other, as on a tilting table. |
| Sinusoidal | Pm ≈ 0.65 Pmax | Oscillating mechanisms where the load follows a sine curve. |
The stepped formula is the one to use on most machines, because a cycle is usually a small number of phases rather than a smooth curve. The other two are shortcuts for cases where the shape is known well enough to skip the summation.
03A conveyor duty, worked through
A transfer carriage runs 4 m loaded at 12 kN per block and returns 4 m empty at 4 kN per block. Total travel per cycle is 8 m. On the face of it the mean is (12 + 4)/2 = 8 kN. The weighted average gives something else:
Roller Pm = [ (1210/3×4 + 410/3×4) / 8 ]3/10 = 9.82 kN
The result is above the arithmetic mean and below the peak, as expected. Sizing on the 12 kN peak instead of 9.64 kN would cost about 2× in calculated life: (12 / 9.64)3 = 1.93. That is the price of using the worst number for the whole cycle.
The roller number sits closer to the peak. With the 10/3 exponent the heavy stroke carries even more weight, so the equivalent load comes out at 9.82 kN rather than 9.64 kN. Same duty, same 12 kN peak: a roller rail is judged against a mean that is nearer its worst case, which is why press and conveyor duties are quoted on the peak and then checked again on the mean.
04Two directions at once: the equivalent load
When the block carries a vertical load and a simultaneous side load, the two are combined before either the mean or the life calculation:
Ps vertical load per block
Pl lateral load per block
Below about 30% of the vertical load, the side component is usually small enough to leave out; above it, the sum is the number that goes into the life equation. The same applies to a block that is pulled upward on one stroke and pushed down on the other: each direction has its own P, and the two directions form the stepped cycle.
05When the cycle is not a neat set of phases
- Log the actual loads. A machine with varying workpiece weight, a press with a varying tonnage, or a robot handling different parts does not have one duty cycle. Take three or four representative cycles and calculate the mean for each.
- Use travel length, not time, unless speed is constant. The formulas accept either L or t as long as the same measure is used throughout; mixing metres and seconds gives a meaningless result.
- Include the dwell. A block standing still under load for a long time does not add travel, but it does load the raceway statically; the static check covers it.
If the duty is genuinely unknown, size on a conservative peak with a higher fSL and revisit the life figure once the machine has run. It is cheaper than replacing blocks in the field.
06Questions we get
Should I size on the peak load or the mean load?
Both, for different checks. The peak decides the static safety factor and the moment; the mean decides the bearing life.
Why is the exponent 3 for balls and 10/3 for rollers?
It comes from the life equation. Ball life varies with load to the power of three, roller life to the power of ten thirds, so the same partial loads average differently.
Do I need to include the return stroke?
Yes, if the carriage is loaded on the return. An empty return pulls the mean down; a machine that cuts both ways keeps it close to the cutting load.
07Where to go next
The size calculator takes a single duty and returns C and life; use this page to prepare the mean load it should be given. Moment load covers the peak side of the same cycle, and the selection guide places both checks in the sizing sequence.
For conveyor and transfer axes: HG series. For press feed and shock loading: RG roller series.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
