Acoustics

Silent guideway selection: buy the right decibels

A silent series changes three things: the recirculation path, the retainer and the end cap. That fixes the noise the block makes. It does not fix the noise the machine makes. Sort the source before sorting the catalogue.

QR · QE · QH · QW Source first 5 min read

01Four noises, one block

When an axis is loud, the guideway is blamed first because it is the part that moves. In practice the sound comes from four places, and only the first two belong to the block:

SourceSignatureWhat fixes it
Ball recirculationContinuous hiss that rises with speed, even, tied to carriage speedSilent recirculation path, retainer chain, damped end cap
Ball-to-ball impactFine rattle at reversal, worst at low load and high speedRetainer that keeps the balls spaced
Rail jointA click once per pass, at the same position every strokeJoint position, staggering and end distance — see rail joints
Wiper and frameLow-frequency rub or a resonance that appears only at one speedWiper preload, panel damping, stiffening — not a new block

The signature column is the practical test. If the sound repeats at exactly the same point in the stroke, it is the rail or the joint. If it tracks speed continuously, it is the recirculation.

02What the silent design changes

Three changes separate a silent family from its standard counterpart, and all three are inside the block:

  • Recirculation path. The return channel is reshaped so the balls turn without the sharp corner that produces the hiss. Longer, gentler turns cost a little block length.
  • Retainer. A chain or wire keeps the balls spaced, so they do not collide with each other as they enter and leave the load zone. This is the change that removes the reversal rattle.
  • End cap. Damped or reinforced material, and a tighter fit, to stop the cap itself acting as a drum.

None of these touch the raceway, so the load rating and the accuracy grades stay in the same family as the standard version. The block is slightly longer, and the price is slightly higher; that is the whole trade.

03The four silent families and where they sit

FamilyRolling elementProfileBest fit
QRRollerStandard heightHeavy gantries in quiet rooms; rigidity with reduced noise
QEBallLow profileMachine fronts and automation cells where height is tight
QHBallHeavy loadLoaded axes that still have to meet a noise target
QWRoller or ball by sizeWide railSingle-track axes with a moment and a noise limit at the same time

Pick the profile first, then the silent variant of it. A low-profile requirement rules out QR regardless of how quiet it is, and a 40 kN block requirement rules out QE.

04Speed, preload and the quiet you actually get

Two settings decide how much of the design change reaches the ear:

  • Preload. A heavier preload raises rigidity and usually raises noise, because every ball is loaded all the time. If the axis is quiet-critical, take the lightest preload that still meets the accuracy requirement.
  • Speed. Recirculation noise scales with speed. A silent block at 100 m/min can still be louder than a standard block at 30 m/min, so the target has to be stated at the real cycle speed, not at a catalogue maximum.

The honest way to specify it: state the sound pressure level you need, at what distance, at what speed, in what enclosure. A supplier who quotes "quiet" without those three numbers is describing a design, not a result.

05What to fix before buying a silent block

Three cheap checks come before any series change:

1 Move the rail joint out of the working stroke and stagger the pair
2 Check the wiper: a dry or over-preloaded wiper rubs and sounds like a bearing
3 Check the frame: a panel resonance at one speed is not a guideway problem

If the click survives all three, it is the joint geometry. If the hiss survives, it is the recirculation, and the silent family is the right purchase.

06RFQ checklist for a noise-limited axis

Target ≤ 62 dB(A) at 1 m, measured at 40 m/min, in the enclosure
Axis 25 size, 2 rails × 900 mm, 2 blocks each, 18 kN
Profile low profile preferred, 40 mm total height limit
Preload light, accuracy H
Ask silent family proposal, measured noise data, and the block length penalty

Asking for the block length penalty matters: a silent block is longer, and on a short stroke that can cost more travel than the noise is worth.

07Questions we get

Does a silent series run slower?

Not usually. The change is in the recirculation path and the end caps, not the raceway, so the speed limit stays close to the standard family. Check the catalogue column for the specific size.

Will a silent block fix a rail joint click?

No. The click comes from the gap and the step between rail ends, and every block passes over it. Fix the joint first, then the block.

Is a roller rail quieter than a ball rail?

Not by itself. Rollers remove ball-to-ball impact but add their own noise; the silent roller families exist because that second problem was engineered out.

08Where to go next

All twenty guides, arranged by decision stage, are on the knowledge hub.

The diagnosis in full is on guideway noise; the joint rules are on rail joints; the preload trade-off is on accuracy and preload. For a single-track quiet axis, read wide rail guideways.

Products: QR silent roller, QE silent low profile, QH silent heavy load, QW silent wide.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts