Engineering
Guideway friction and drive force: sizing the motor
A rolling guideway is not frictionless, and the number that matters for the drive is not the coefficient but the total force at the worst orientation. Horizontal axes are dominated by seals; vertical axes by gravity.
01Where the resistance comes from
Three sources add up, and they do not scale the same way:
- Rolling friction at the raceway. Proportional to load, and small: the coefficient is in the thousandths.
- Seal and wiper drag. Roughly constant per block, almost independent of load, and it dominates on a light carriage.
- Grease shear and preload. Rises with preload class and falls as the block warms up, which is why a cold machine can feel stiff for the first few minutes.
On a 500 kg carriage at 5 m/min, the rolling term is a few newtons and the seals are tens of newtons. On a 5 tonne gantry, the order reverses. Sizing a motor from the coefficient alone gets both cases wrong.
02The coefficients, and what they mean in practice
| Guideway type | Coefficient | Comment |
|---|---|---|
| Ball guideway | About 0.004 | Close to constant from crawl speed to full speed, which is what makes precise positioning possible. |
| Roller guideway | About 0.003 | Lower on paper, but higher preload and seal drag usually cancel the advantage on a real axis. |
| Sliding (box) way | 0.05–0.15 | Reference point only: a rolling guideway is roughly 1/50 of this, and that is the reason it replaced hand-scraped ways on most axes. |
The coefficient is a property of the rolling contact, not of the rail size. A 15-class block and a 45-class block have the same μ; what changes is the load W and the seal drag per block.
03The drive force by orientation
Gravity enters differently depending on how the rail is mounted. Use the expression for the actual mounting, not the horizontal one by default:
| Mounting | Drive force | What dominates |
|---|---|---|
| Horizontal | F = μW + S | Seal drag S; the rolling term is small. |
| Vertical | F = W + μW + S | Gravity. The guideway is only a small addition to the hoisting force. |
| Inclined θ | F = W sinθ + μW cosθ + S | Depends on the angle; at 30° gravity is already half the weight. |
Then add the acceleration term and a motor margin:
Peak demand F_peak = F + F_acc
Motor margin 1.5–2.0 × F_peak
The margin covers seal drag variation, cold grease, rail misalignment and the fact that a servo should not run at its continuous limit during every cycle.
04An 8.8 kN carriage, three ways
Same carriage, same rails, mounted three different ways. Seal drag is taken as 25 N, which is typical for four blocks with standard wipers:
| Orientation | Drive force at constant speed |
|---|---|
| Horizontal μW = 0.004 × 8,800 | 35 N + 25 N = about 60 N |
| Inclined 30° | 4,400 N + 30 N + 25 N = about 4,455 N |
| Vertical | 8,800 N + 35 N + 25 N = about 8,860 N |
The horizontal case is almost all seal drag: the rolling contact contributes 35 N out of 60 N. That is why a light, fast axis feels dominated by wiper quality and rail cleanliness rather than by bearing size.
Do not size a vertical axis from μ. At 0.003 or 0.004 the coefficient is irrelevant next to the weight. The motor, brake and counterbalance are chosen from the mass, and the guideway only decides how much extra drag and stick-slip appears at low speed.
05Ball or roller, on friction alone
The difference between 0.004 and 0.003 on an 8.8 kN carriage is 8.8 N. That is less than a typical wiper pair contributes, and far less than the extra preload force of a roller block. Friction alone will never justify the price difference.
Rollers are chosen for rigidity and moment capacity, and the friction penalty is accepted as part of that. The full comparison is in ball vs roller guideway; the friction numbers here are the ones to use once the type is fixed.
06Stick-slip, and why slow axes chatter
At very low feed rates the block can alternate between sticking and slipping instead of sliding smoothly. The cause is usually a boundary lubricant film combined with high preload, and it shows up as a jerky motion that the servo cannot tune out.
- Light preload and a slightly larger block reduce the tendency.
- Oil lubrication instead of grease helps on very slow, continuous motion.
- Check rail parallelism first: two rails fighting each other produce the same symptom at any speed.
Stick-slip is a motion-quality problem, not a load problem. Measuring the pull force in both directions with the drive disconnected separates it from a sizing error in a few minutes.
07Questions we get
Does a roller guideway need a bigger motor than a ball guideway?
Slightly, but not because of the coefficient. Higher preload and stiffer contact raise seal drag and acceleration force; the friction coefficient itself is lower.
Does preload increase friction?
Yes. Preload presses the rolling elements into the raceway before any external load arrives, so drag rises with the preload force.
Why does my axis need far more force than the formula predicts?
Check dry or over-tightened wipers, non-parallel rails, and drag from the screw or belt. A misaligned rail pair can multiply the calculated force several times.
How do I measure the real friction on a machine?
Disconnect the drive and pull the table at constant speed with a force gauge, in both directions. The difference between directions tells you whether the rails are preloaded against each other.
08Where to go next
Load and life come before drive force: run the size calculator first, then use this page for the motor. The lubrication guide explains why a dry block drags, and accuracy and preload covers how preload class changes both stiffness and drag, and noise covers the acoustic side of the same friction.
Low-drag blocks for fast axes: EG low profile and QE silent low profile. Heavy axes where friction is secondary: RG roller series.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
