Hold position

Locking linear guideways: holding a position without a brake

Some axes have to stay where they are when the drive is off: a vertical lift, a measurement station, a manual load point. A lockable rail does that at the carriage instead of at the motor, and the difference matters when the screw is not meant to carry the holding force.

TGR 15–55 Clamp at the carriage 5 min read

01Where the holding force should act

A motor brake holds the screw, the screw holds the nut, the nut holds the carriage. Every element in that chain carries the holding load, and any backlash in it becomes drift. A rail clamp holds the carriage directly against the rail, so the screw and the nut are unloaded while the axis is parked.

That is the whole argument. It matters most where the screw is long, where the nut is preloaded lightly, or where a vertical load would otherwise back-drive the screw.

02The locking rail family

SizeRail width, mmRail thickness, mmMounting screw
TGR15157.7M4
TGR20209.7M5
TGR252511.3M6
TGR303014.3M8
TGR353514.3M8
TGR454520.3M12
TGR555523.5M14

The table above is the rail, not the clamp. The clamp is a separate element that rides the same profile, which is why the rail can be used as a normal guideway and only the hold points need the clamp.

03What the lock does and does not do

DutyRail clampMotor brake
Hold a parked vertical loadYes, at the carriageYes, through the screw
Emergency stop from speedNo; wears the railYes, with a rated brake
Hold with the screw unloadedYesNo; the screw carries it
Multiple independent holds on one railYes, one clamp per carriageNo; one brake per motor
Usable strokeReduced by the clamp zoneFull

Clamping at speed is the mistake to avoid. The clamp is a holding device: bring the axis to rest, then engage it. A clamp used as an emergency brake will flat-spot the rail and destroy the running accuracy in one event.

04Planning the hold points

The clamp body occupies rail length outside the carriage envelope. On a short axis, two hold points at the ends can consume a meaningful part of the travel, so the rail length has to be chosen with the clamps in the drawing, not after.

  • Mark the hold positions first, then subtract the clamp envelope from the stroke.
  • Keep the clamp out of the zone where the carriage reverses most often; that is where rail wear is already highest.
  • If the axis is vertical, check the holding force against the clamp rating with the load at the worst position, not the average.

05When a brake is the better answer

  • Safety stop. A vertical axis that must stop on power loss needs a brake rated for the mass and the speed, not a clamp.
  • Full stroke. If the axis has to hold anywhere, the clamp has to be able to travel with the carriage, which is a different mechanism.
  • Cost. On a small axis a brake motor is usually cheaper than a lockable rail plus clamps.

The combination that appears in practice: a brake motor for safety, plus a rail clamp for the load/unload position where the screw should not be loaded for hours.

06Questions we get

Does a locking rail hold a load or just stop it drifting?

It holds position and can resist a steady load. It is not a brake for a moving mass: clamping at speed wears the rail. Stop first, then clamp.

Locking rail or motor brake?

A brake acts through the screw and is the usual answer for a vertical safety stop. A rail clamp acts at the carriage and is better when the screw must stay unloaded or when several carriages need independent holds.

How much stroke does the lock cost?

The clamp envelope sits outside the carriage, so the locked zone cannot overlap the working stroke. On a short axis that is real travel; plan hold positions before choosing rail length.

07Where to go next

All guides are listed on the knowledge index and grouped on the knowledge hub. Mounting orientation is covered on mounting orientation; the clamp rail belongs to the series comparison; the load arithmetic on moment load.

Products: linear guideways. Send the axis orientation, the held mass and the hold positions, and we will confirm whether a clamp or a brake is the right device.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts