01The two families side by side
Both families are four-row ball guideways with the same rail profile, the same mounting hole pattern and the same accuracy and preload options. Read the ratings across the two catalogue pages and the columns that change are height, carriage mass and a handful of carriage dimensions.
The table below is the comparison that matters. Values are reference figures for standard four-row blocks; the drawing and the inspection sheet for the part you order govern the delivered item.
| Size | H, TGH | H, TGL | Height saved | C, kN | C0, kN | MR / MP / MY, kN·m |
|---|---|---|---|---|---|---|
| 15 | 28 | 24 | 4 | 11.38 | 25.31 | 0.17 / 0.15 / 0.15 |
| 20 | 30 | — | — | 17.75 | 37.84 | 0.38 / 0.27 / 0.27 |
| 25 | 40 | 36 | 4 | 26.48 | 56.19 | 0.64 / 0.51 / 0.51 |
| 30 | 45 | 42 | 3 | 38.74 | 83.06 | 1.06 / 0.85 / 0.85 |
| 35 | 55 | 48 | 7 | 49.52 | 102.87 | 1.73 / 1.20 / 1.20 |
| 45 | 70 | 60 | 10 | 77.57 | 155.93 | 3.01 / 2.35 / 2.35 |
| 55 | 80 | 70 | 10 | 114.44 | 227.81 | 5.66 / 4.06 / 4.06 |
Two things stand out. The rating columns are identical, so nobody gains load capacity by choosing the taller family. And the height saved grows with size: 4 mm at 15 and 25, 3 mm at 30, then 7 and 10 mm from 35 up. On a small axis the difference is invisible; on a 45 or 55 rail it is a centimetre of machine height.
02Where the height difference comes from
The rail is common. Rail width, rail height, hole pitch and the bolt size are the same in both tables, which is why a TGH rail and a TGL rail of the same size are interchangeable in the base plate. The carriage is what changes.
Look at the carriage section numbers rather than the headline H. In the 15 size the standard carriage carries a 7.95 mm body above the ball rows and the low-profile one 3.95 mm; the 4 mm that leaves the drawing is the same 4 mm that leaves the machine. The ball rows, the return path and the seal arrangement stay where they are.
That is the engineering compromise in one sentence: the low-profile family removes material from the top of the carriage, not from the raceway. It keeps the four rows, the preload range and the load ratings, and gives up section depth. A shallower section has a smaller second moment of area, so under the same moment it deflects more. The load at which the raceway takes permanent deformation does not change, because that is set by the ball and groove geometry, not by the housing depth.
Carriage mass follows the same logic: 0.18 kg against 0.14 kg at size 15, 1.45 kg against 1.14 kg at 35, 4.17 kg against 3.25 kg at 55. Rail mass per metre is identical in both tables, which is the clearest sign that the running surface is shared.
03What the millimetres cost in the stack
Height in a linear axis is not one number, it is a chain. Base plate, rail, carriage, moving plate, tooling. Change the carriage by 10 mm and every element above it moves, and so does everything that has to line up with it.
- The screw nut. The nut centre sits at a fixed height above the base. If the carriage drops, either the nut housing grows or the screw axis drops with it. Both are redesigns, not adjustments.
- The motor and coupling. A drop in table height usually means a change in the motor bracket or in the coupling offset.
- Stacked axes. On a two-axis or three-axis stack, the saving multiplies: 4 mm on the lower axis lifts the upper axis by 4 mm, and the gantry by the same amount again.
- The enclosure and the guard. A lower profile often buys the clearance for a cover, a bellows or a way to keep the working plane below the operator's sight line.
Where the axis is a single horizontal slide on a flat bed, the 4 mm is irrelevant and the choice falls to price and lead time. Where the axis sits under a table, inside a housing, or in a stack of three, the height column is the first thing to read.
04Rigidity: lower is not stiffer
A common assumption is that the low-profile block is stiffer because the load path is shorter. The catalogue does not support that. The allowable static torque is the same in both families, so the moment at which the raceway yields is the same. What differs is elastic deflection before that point.
Under a roll moment the carriage rocks on its ball rows. The resisting couple depends on the distance between the rows and on how the housing carries the moment into the moving plate. Removing 10 mm of housing depth reduces that lever, so the same moment produces more angular deflection. If the axis is a precision gantry, a measuring stage or a machine that reverses direction under load, that deflection shows up as lost accuracy at the tool, not as a broken rail.
The practical answers, in the order that costs least: raise the preload one grade, increase the carriage length from CA to HA, widen the rail spacing, or move up a size in the standard-height family. Preload buys stiffness with life; the others buy it with space.
05The swap trap
Because the rail is shared, it is tempting to treat TGH and TGL as interchangeable blocks on the same rail. Mechanically they will bolt on. Geometrically they will not sit at the same height, and that breaks three things at once: the table plane, the screw nut alignment and any dowel-pinned tooling that was set to the old height.
If a machine is being re-designed and the stack height is open, the swap is free. If a machine is in service and someone proposes the low-profile block as a drop-in replacement, the honest answer is that the base plate, the nut housing and often the motor bracket have to be revisited. We mark both families with the same rail section in the catalogue, and that is exactly why the height column has to be read twice.
Check before ordering. Send the rail size, the existing part code and the height of the moving plate above the base. We confirm whether the low-profile carriage fits the existing stack, or whether the nut housing has to change with it.
06When TGH earns its height
The standard-height family is the safer default in four situations.
- High centre of gravity. A tall workpiece on a narrow carriage produces a roll moment that grows with height. The deeper carriage section resists it with less deflection.
- Cantilever and overhang. Tooling that hangs off the carriage, or a load whose centre sits outside the block line, turns force into moment. The taller section keeps the angular error smaller.
- Preload at the top of the range. ZB preload in a shallow housing concentrates the preload force on a thinner section. Where high stiffness is the point of the design, the standard body is the better host.
- Vertical and wall-mounted axes. Gravity acts across the carriage rather than down onto it, and the moment arm is set by the mounting face. The taller block gives more material where the load path turns.
None of this shows up in the C and C0 columns. It shows up as deflection, as surface finish, as a positioning error that appears only when the axis is loaded.
07When TGL is the right call
- Height-limited stacks. Multi-axis gantries, table-top automation and machines built into an existing enclosure, where every millimetre between the base and the working plane is already allocated.
- Long, light axes. Transport, pick-and-place and measuring slides where the moving mass matters more than the moment, and where the lighter carriage trims the inertia the motor has to accelerate.
- Clean environments. Semiconductor handling, inspection and laboratory stages, where the lower profile sits under a cover and the carriage mass is part of the settling time.
- Where the moment is already small. A centred load on a wide base does not need section depth; it needs a rail that fits.
The catalogue lists this family against automation equipment, high-speed transport, precision measuring instruments, semiconductor equipment and woodworking machinery, which is a fair summary of where the height budget is tighter than the moment budget.
08Questions we get
Do TGH and TGL carry the same load?
Yes, at every shared size. C, C0 and the three static torques are identical, and so is the rail section.
Can I swap a TGL carriage onto a TGH rail?
The rail fits, the height does not. Treat it as a re-build of the stack, not a part swap.
Is the lower carriage less rigid?
The yield moment is the same; elastic deflection is higher. Preload one grade closes most of it.
Which size has no low-profile option?
Size 20 in the table we build from. Ask for the drawing before designing around the standard block.
09Where to go next
If the family is settled and the block length is not, the next decision is CA against HA: the long carriage buys rating and stiffness with stroke. If the load case is still open, the load and life calculator returns the load per block and the required C, and the size chart puts the ratings for every size in one place.
Deflection under an offset load is a moment question: moment load covers MR, MP and MY and the overhang formula. The stiffness that follows the choice is set by accuracy grade and preload, and the family map for everything else is in the series comparison. All guideway families sit under linear guideways.
Send the rail size, the stack height and the load case through the inquiry form and we come back with the family, the block type and a checked height chain.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
