Cross reference

Linear guideway replacement: what matches, and what only looks like it does

Most replacement requests start with a photo of a block and a question about the price. The answer depends on three numbers that are not in the photo: rail width, block height and hole pitch. This page maps the common series to ours, then lists the four checks that decide whether a swap is safe.

Eight series mapped Four checks before ordering 6 min read

01How to read the table

The table maps the series designations that appear on most machine drawings to the families we build. It is organised by what the designation actually controls, not by name similarity. Two letters that look alike can describe a standard-height block and a low-profile one, and those are not interchangeable.

Read it in three steps. Find the designation on your drawing in the first column. Confirm the rail width class in the third column against the rail in the machine. Then use the fourth column to see which property carries over and which one does not.

02Series cross-reference

Designation on drawingOur seriesRail widthsWhat carries overWhere it is used
HG (HGH / HGW)HG15–65Four-row ball, equal load in four directions, standard mounting heightMachining centres, gantries, general automation
EG (EGH / EGW)EG15–35Low-profile block, reduced mounting height, four-direction loadPackaging lines, electronics assembly, compact slides
MG (MGN / MGW)MG7–15Miniature section, stainless option, low load envelope3D printers, lab stages, small pick-and-place heads
RG (RGH / RGW)RG15–65Roller contact, higher rigidity and shock capacity, different life baseHeavy cutting, press transfer, shock-loaded axes
WE (WEH / WEW)WE20–65Wide rail, one line resists roll momentCantilever heads, single-rail gantries
Silent variantsQH / QE / QWSame as base familyQuieter ball return inside the same envelope; load rating unchangedMachines with an operator nearby or a noise spec
Anti-torqueCGBy series pageBlock resists rotation under an offset loadOffset and overhung tool heads
Ultra heavy rollerURBy series pageLargest roller section for press and lifting framesPress frames, lifting and transfer axes

The widths above are the classes each family is catalogued in, not a guarantee that every size in that class exists. Where a table cell says "by series page", the family is organised by load class rather than by width, and the series page carries the actual list.

03The four checks

All four are dimensional. None of them can be settled from a catalogue table alone, because rail length and end distance change with the order.

1

Rail width

Measure across the rail body, not the block. Two rails of the same nominal size can differ by a millimetre in body width between families, and the block cannot be reseated on a raceway of another width.

2

Block height

Height decides where the table sits relative to the screw axis. A standard and a low-profile block differ by several millimetres, which shows up as a misaligned coupling rather than as a visible gap.

3

Hole pitch and end distance

Check the pitch between mounting holes and the distance from the last hole to the rail end. The pitch usually follows the mounting standard for the width class; the end distance does not, and it is what breaks a rail that was ordered to a different length.

4

Accuracy and preload codes

Read the marking on the block. A replacement carries the accuracy of the rail it runs on, so a high-grade block on a standard rail does not deliver the grade. Preload is set across the pair for the same reason.

The dimensional tolerances behind each check are on the size chart, and the grades and preload codes are explained in accuracy and preload.

04When a swap does not work

SituationWhy it fails
Standard block onto a low-profile railThe raceway sits at a different height in the block, so the ball rows never load correctly even when the bolt holes align.
Ball block on a roller railDifferent rolling element and groove geometry. The block will not seat, and the load rating it promises does not apply to the rail.
Mixed suppliers on one axisPreload and parallelism are set across the pair. Two suppliers cannot guarantee a matched set, and the error appears as uneven running rather than as a hard stop.
Replacement rail ordered to a nominal lengthEnd distance changes with the length. A rail cut to the nominal figure can miss the last mounting hole by the amount the original was trimmed.
Sealing class carried over from the old partWiper codes are additive, not equivalent. A heavier seal on a clean high-speed axis adds drag and heat without adding life.

Each of these is cheap to avoid at the quotation stage and expensive to find at assembly. This is why the request we send back is always a drawing, not a price.

05Questions we get

Can a replacement block run on my existing rail?

Only if the rail width class, raceway form and ball or roller size match. A block from another width class will not seat on the raceway even when the bolt holes line up.

Does a replacement change the accuracy grade?

When blocks and rails from different batches are mixed, yes. Accuracy belongs to a matched pair, so a replacement block carries the grade of the rail it runs on.

Will the mounting height be the same?

Not between a standard and a low-profile family. The difference is several millimetres, and it moves the table relative to the screw axis.

Are the hole pitches identical across suppliers?

Commonly for the same width class, because most catalogues follow one mounting standard. End distance still varies with rail length and series, so the drawing governs.

Can I mix two suppliers on one machine?

On separate axes it is workable once each pair is verified. On the same axis it is not, because preload and parallelism are set across the pair.

What do you need to quote a replacement?

The block marking, rail width, rail length, block count, the accuracy and preload codes, and a photo of the mounting face.

06Where to go next

If the designation is known and the axis can be re-shortlisted rather than replaced one-to-one, start at series comparison to see what the families solve. Where the constraint is ball against roller rather than brand against brand, ball vs roller settles it on life base and rigidity. If a single rail has to carry an overhung head, moment load covers what the block has to resist, and installation covers the alignment work after a swap.

Sizing comes after the family is fixed: the calculator returns load and life, and the selection guide sets the order of decisions. Once the replacement is confirmed, how an order runs sets out what the quotation fixes and what to send with the enquiry. Send the marking and a photo through the inquiry form and we will confirm the cross-reference before quoting.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts