01What the flange does
A plain bearing needs a housing: a bored hole, round within a hundredth, with a shoulder to stop the sleeve walking. A flanged bearing carries that shoulder in its own body and bolts to a plate, so the plate only needs a clearance hole for the shaft and four bolt holes.
The trade is stiffness: the housing wall is replaced by the plate thickness. If the plate is thin, the flange tilts and the bearing preloads at one end of the stroke.
02The flange shapes
| Shape | Bolt pattern | Best for |
|---|---|---|
| Square flange | Four bolts on a rectangle | Cantilever loads; resists moment in both planes |
| Round flange | Four bolts on a circle, or two | Small footprint, rotating mounts, tight envelopes |
| Compact / twin flange | Short pattern close to the bore | Where the plate is small; the load sits nearer the bore |
The letter code in the family name follows the same logic: F for flanged, K for the square or keyed variant, H for the longer body, and the trailing letters describe the seal or the housing style. Read the size drawing, not the letters alone — the same size designation can differ between families.
03Body length is the moment capacity
A single short bearing on a shaft resists almost no moment. The flange does not change that; the body length does. Long-body and double-body variants exist precisely for this:
| Body | Moment capacity | Use |
|---|---|---|
| Single standard | Low; needs a second bearing | Short stroke, guided by two bearings |
| Double / long | Roughly doubled arm | Cantilever head, one bearing instead of two |
| Heavy / large diameter | High, with a bigger shaft | Transfer units, lift guides |
Two short bearings on one shaft cost more, take more length and need both flanges aligned. One long bearing usually aligns itself and is the cheaper answer for a single cantilever.
04Fit and bolt order
Clearance adjustable (SDM class) or fixed (SDE class)
Bolt order cross pattern, shaft through the bore, then torque
Tightening the flange before the shaft is in the bore pulls the bearing out of round and the shaft will not enter. That is a sequence error, not a tolerance error, and it is the most common cause of a "tight" flanged bearing.
05Plate design rules
- Plate thickness at least the flange thickness, and preferably thicker; a thin plate is a flexible housing.
- Bolts close to the bore, not spread to the corners of a large plate.
- Support the plate under the flange; a plate spanning a gap bends under load.
- Use a shoulder or a dowel if the flange must not move; bolts alone locate by friction.
- Leave room for the wiper to be replaced without removing the plate.
06Questions we get
Square or round flange?
Square puts four bolts on a rectangle and resists moment in both directions; round fits a smaller footprint. Square is the safer default for a cantilever.
Why does the flange bearing tilt on my plate?
The plate flexes between the bolts, or the bolts were tightened before the bearing was seated. Use a flat thick plate and tighten in a cross pattern with the shaft in the bore.
Can a flanged bearing carry the same load as a housed one?
The bearing is the same; the load path differs. A flange spreads it over the bolt pattern, a housing around the bore. A thin plate under a flange is weaker than a thick housing wall.
07Where to go next
All guides are listed on the knowledge index and grouped on the knowledge hub. The plain-bearing decision is on linear bearing selection; the shaft on linear shaft selection; the geometry on cylindrical against square.
Products: linear motion range. Send the shaft diameter, the plate thickness and the bolt pattern, and we will confirm the flange and the body length.
Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.
This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.
Buying Precision Motion Components from China
is Your Best Choice!
Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.
Cookie preferences
Choose which categories this site may use. Necessary cookies cannot be switched off.
