Clearance and fit

Linear bearing selection: clearance, series, housing fit

A linear bearing is a bushing with balls, and almost every problem attributed to the bearing is a fit problem: the shaft at one end of its tolerance, the housing at the other, and the clearance never checked. Three decisions avoid it.

SDM · SDE · LM h6 / H7 5 min read

01The three decisions

  • Clearance type: adjustable, fixed, or preloaded through the housing.
  • Series and length: standard, long, miniature, or heavy-duty, which sets the load and the moment capacity.
  • Mounting: plain bore in a housing, or a flange that bolts to a plate.

Get the order right. Clearance follows the fit, the fit follows the housing, and the housing follows the mounting. Choosing a flange first and a clearance last is how a line ends up with bearings that are either loose or tight, batch after batch.

02Clearance: the decision that is usually skipped

TypeBehaviourWhere it belongs
Adjustable (SDM)A slit housing with set screws compresses the outer sleeveHousing bored in place; shaft at the upper tolerance; a small preload wanted
Fixed (SDE)Clearance set at the factory, no adjustmentInterchangeable replacement, volume production, no rework risk
Preloaded by housingA slight interference squeezes the sleeveZero-play axes; needs a controlled bore, not a hammer

An adjustable bearing overtightened is worse than a fixed one with clearance: it raises friction, heats the shaft and wears the raceway in one band. Set it with the carriage moving, not on the bench.

03The series, by what they are for

SeriesFeatureUse
SDM / SDEMetric standard, adjustable or fixedThe default automation bearing
LM / LMEMetric and inch standard rangesReplacement for imported machines; check the bore series
LMB / LB / LBELong body, large diameterCantilever and heavy radial load; one bearing instead of two
KHMiniature short bodyInstrument-scale axes, 3D printer heads
Flange variantsRound, square or compact flangePlate mounting without a bored housing

Long-body bearings are the cheapest way to add moment capacity to a shaft axis: the same diameter, twice the length, twice the moment arm. If the design already needs two bearings side by side, one long bearing usually costs less and aligns itself.

04Fit: shaft and housing

Shaft ground to h6 is the common band; g6 for a light push fit
Housing bored to H7, round within 0.01 mm
Result the bearing's internal clearance, not the fit, decides the play

Two checks catch most fit problems before assembly:

  • Measure the shaft at three points along the stroke. A shaft that is at the top of the band in the middle will be tight there and loose at the ends.
  • Check the housing for out-of-round with a bore gauge in two directions. A three-jaw chuck leaves a triangle that no bearing can survive.

05Load direction and mounting holes

A linear bearing carries load in the direction its rows are arranged for. In a shaft axis, the load usually points down, and the bearing rows are symmetric about that direction, so radial load in any direction is acceptable; the limit is the moment, not the direction.

When the bearing is flanged, the bolt pattern sets the position and the flange carries the load. Keep the bolts close to the bore, and use a plate thick enough that the flange does not tilt: a tilted flange preloads the bearing at one end of the stroke and unloads it at the other.

06Lubrication and wipers on a shaft axis

Most shaft bearings are greased for life, and most of them die from contamination rather than from load. The wiper is the part that decides the life:

EnvironmentWiperNote
Clean room, labStandard lipLow friction, low drag
General workshop dustDouble lipKeeps fine dust out of the ball track
Chips and coolantMetal scraper plus lipScraper takes the chip, lip takes the film
WashdownStainless bearing and shaftThe wiper alone will not stop corrosion

07Questions we get

Adjustable or fixed clearance?

Adjustable suits a housing machined in place and a shaft at the upper tolerance. Fixed is right for interchangeable replacement, because nobody can over-tighten it on the line.

Why does the bearing rattle when the load reverses?

The fit or the clearance is loose, or the load direction changes and the balls unload. A light preload removes the rattle; a loose housing bore has to be re-bored or sleeved.

Can a flanged bearing replace a housing?

Yes, and it is the usual way to mount on a plate without boring. The flange carries the load and the bolt pattern sets the position, but the plate must be stiff between the bolts.

08Where to go next

All twenty guides are on the knowledge hub. The shaft these bearings run on is on linear shaft selection; the geometry decision on cylindrical against square; the friction and drive force on friction and thrust, and the sizing arithmetic on the load and life calculator.

Products: linear motion range. Send the shaft diameter, the housing bore and the load direction, and we will confirm the series and the clearance.

Part of the MS Linear product selection library — the engineering notes behind our linear guideways, ball screws, modules, shafts and bearings. For the full range, browse the MS Linear catalogue or the selection library index.

This page covers the essentials. For the complete selection PDF, full part-number tables and a matched recommendation, contact MS Linear or email [email protected] — we will send the relevant selection PDF for your load case.

China Factory Direct · Drop-in Compatible Dimensions

Buying Precision Motion Components from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts