LM and LME Linear Bearings: Metric and European Standard

LM and LME Linear Bearings: Metric and European Standard
+

Key Features

Metric and European bodies in the same family; the longer LME spreads load at the same bore.

5 mmMinimum bore (LME)
2Standards
3Body types

Applications

Machine retrofits European machinery Linear slides Assembly cells Measuring fixtures

Linear Bearings · LM and LME Linear Bearings: Metric and European Standard

Technical Description and Selection Reference

Product Overview

The LM and LME series are the metric and European-standard linear bearings. LM follows the Asian bore and length series, LME the European one; both are built with steel cages, sealed ends and the same three variants as the SDM family: closed, adjustable and open.

The difference that matters in practice is the length and the load: at the same bore, the European body is often longer, which spreads the load and lowers the contact pressure. A machine designed around a European bearing will not accept a short Asian body without losing stiffness, so the series is chosen from the drawing, not from the bore alone.

Bores run from 5 mm in the LME series upward, with LM covering the larger metric steps. Radial clearance, eccentricity and the housing fit are quoted per size; the bearing guide explains how to read them.

ParameterSpecification
SeriesLM metric / LME European linear bearing
Bore rangeLME from 5 mm; LM covering the larger metric steps
VersionsClosed, AJ adjustable, OP open
Ball cageSteel cage, four circuits
Shaft toleranceh6 or g6
Housing boreH7 for the closed type
SealsUU double seal standard
Radial clearanceQuoted per size, class on request
EccentricityQuoted per size in the datasheet
LubricationGrease pre-filled; oil for continuous duty
Minimum order1 piece
Lead time3–7 days for stock bores

Product Features

  • European body length available where the drawing calls for LME, without changing the shaft.
  • Steel cage and four circuits keep the load centred on a long stroke.
  • Adjustable version restores clearance on a worn shaft.
  • Open version for supported shafts and pass-through rails.
  • Sealed ends and a grease reservoir for maintenance intervals longer than a shift.

Applications

When replacing a European bearing, send the original part number: the LME length and tolerance band are matched, so the housing does not have to be re-machined.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

SDM is the Asian-standard sleeve, LM the metric series and LME the European series. At the same bore, the European body is often longer, which spreads the load and lowers contact pressure. The series is chosen from the drawing and the housing length, not from the bore alone.

The closed type has a fixed clearance class; the AJ adjustable type has a split housing that is tightened until the play is gone. Adjust with the shaft in place, move the carriage over the full stroke, and stop at the point where it still glides without drag. A preloaded sleeve runs hotter and shorter-lived, so do not over-tighten.

Shaft h6 or g6, housing bore H7 for the closed type. The bore tolerance of the bearing is quoted per size, and the fit is what decides whether the axis feels tight or loose. Send the shaft drawing with the order and the pair is checked before shipment.

Yes, an open block carries less moment than a closed block of the same size because the race is interrupted. It is used where the shaft must pass a support rail, and the support spacing, not the bearing, then sets the accuracy.

Sleeves are grease-filled at assembly. Refill at the interval in the lubrication guide, which depends on speed and duty: a slow axis can run for months, while a fast axis needs a shorter interval. Oil is used above the grease speed limit.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Linear Bearings from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts