SDM Linear Bearing: Closed, Adjustable and Open, 6 mm Up

SDM Linear Bearing: Closed, Adjustable and Open, 6 mm Up
+

Key Features

Steel-caged sleeve in closed, adjustable and open bodies, with the clearance class quoted per size.

6 mmMinimum bore
H7Housing bore
3Body types

Applications

Shaft axes Pick-and-place Cutting heads Printing units Test rigs Door drives

Linear Bearings · SDM Linear Bearing: Closed, Adjustable and Open, 6 mm Up

Technical Description and Selection Reference

Product Overview

The SDM series is the Asian-standard linear bearing: a steel-caged ball sleeve that runs on a hardened shaft, with a nominal bore tolerance held to a few microns. Three versions sit in the same family: the standard closed type, the AJ adjustable type with a split housing, and the OP open type for a supported shaft.

Bores start at 6 mm and run through the common metric steps. The adjustable type lets a worn or slightly undersize shaft be brought back to zero clearance by tightening the housing, which is the practical fix on a machine that has run for years. The open type is for a shaft that has to pass a support rail.

Fit matters more than the catalogue number: the shaft is usually h6 or g6, the housing bore H7, and the clearance class decides whether the axis feels tight or loose. The linear bearing guide walks through the fits, and the shaft guide covers the matching shaft.

ParameterSpecification
SeriesSDM linear bearing, Asian standard
Bore range6 mm upward through the metric steps
VersionsSDM closed, SDM-AJ adjustable, SDM-OP open
Ball cageSteel cage, four ball circuits
Shaft toleranceh6 or g6
Housing boreH7 for the closed type
SealsUU double seal standard
ClearanceAdjustable on the AJ type; fixed class on the closed type
Operating temperatureConfirmed at quotation for the selected seal compound
LubricationGrease pre-filled; oil for high speed
Minimum order1 piece
Lead time3–7 days for stock bores

Product Features

  • Steel cage holds the ball circuits square, so the sleeve does not skew on a long stroke.
  • AJ version can be tightened back to zero clearance instead of replaced.
  • OP version passes a supported shaft without a second bearing.
  • UU seals on both ends keep chips out of the race.
  • Bore tolerance is quoted, not implied: the fit to the shaft is part of the order.

Applications

Pair with an SF shaft for a plain, low-cost axis, or move to a ball spline when the same shaft has to carry torque.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

SDM is the Asian-standard sleeve, LM the metric series and LME the European series. At the same bore, the European body is often longer, which spreads the load and lowers contact pressure. The series is chosen from the drawing and the housing length, not from the bore alone.

The closed type has a fixed clearance class; the AJ adjustable type has a split housing that is tightened until the play is gone. Adjust with the shaft in place, move the carriage over the full stroke, and stop at the point where it still glides without drag. A preloaded sleeve runs hotter and shorter-lived, so do not over-tighten.

Shaft h6 or g6, housing bore H7 for the closed type. The bore tolerance of the bearing is quoted per size, and the fit is what decides whether the axis feels tight or loose. Send the shaft drawing with the order and the pair is checked before shipment.

Yes, an open block carries less moment than a closed block of the same size because the race is interrupted. It is used where the shaft must pass a support rail, and the support spacing, not the bearing, then sets the accuracy.

Sleeves are grease-filled at assembly. Refill at the interval in the lubrication guide, which depends on speed and duty: a slow axis can run for months, while a fast axis needs a shorter interval. Oil is used above the grease speed limit.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Linear Bearings from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts