SF Series Solid Linear Shaft: Metric 3–150 mm, HRC 60–62

SF Series Solid Linear Shaft: Metric 3–150 mm, HRC 60–62
+

Key Features

Case-hardened GCr15 shaft with a soft core, ground to h6 or g6 and machined to your drawing. The running surface resists wear while the ends stay machinable.

3–150 mmDiameter
HRC 60–62Hardness
6000 mmMax length

Applications

Linear bearing shafts Guide rods Pneumatic cylinders Printing presses Packaging lines Test rigs Medical tables Gate actuators

Linear Shafts · SF Series Solid Linear Shaft: Metric 3–150 mm, HRC 60–62

Technical Description and Selection Reference

Product Overview

The SF series is the metric solid shaft of the MS Linear shaft range, ground from GCr15 bearing steel and hardened to HRC 60–62. It is the shaft an engineer reaches for when the axis is a plain linear bearing, a clamp, a pivot or a support along which a carriage runs.

Diameters run from 3 mm to 150 mm and single-piece lengths to 6000 mm; longer runs are supplied as butted lengths with a dowel or threaded joint, machined so the joint does not stand proud of the running surface. Ends can be threaded, stepped, keyed, drilled or tapped, and the finished part can carry hard chrome.

The running surface is supplied in h6 or g6, so the shaft can be matched to the housing bore of an adjustable or fixed linear bearing. It is not a drop-in substitute for a profile rail: the shaft carries point loads through a sleeve, so support spacing and deflection have to be checked, which is covered in the shaft selection guide.

ParameterSpecification
SeriesSF solid linear shaft, metric
Diameter range3 mm to 150 mm, ground in steps
MaterialGCr15 bearing steel (SUJ2)
HardnessHRC 60–62 through the case
Case depth0.4–0.7 mm below 6 mm; 0.6–1.5 mm 10–15 mm; 0.8–2.0 mm 16–20 mm; 0.8–3.0 mm above 25 mm
Toleranceh6 or g6, per size table
Maximum length6000 mm in one piece; longer by butted joint
StraightnessPer length class, checked on the bench
SurfaceGround; hard chrome optional
End machiningThread, step, keyway, radial holes, coaxial bores
Minimum order1 piece
Lead time3–7 days standard; 10–15 days with end machining

Product Features

  • Case-hardened surface with a soft core, so the shaft resists wear without becoming brittle at the ends.
  • h6 and g6 stock tolerances match the bore of adjustable SDM and LM bearings and remove the need to ream a housing.
  • Straightness is checked over the full length, not sampled at the ends, because a bowed shaft shows up as a tight spot mid-stroke.
  • End machining is done after hardening and before final grinding, so the thread and the running surface stay concentric.
  • Butted joints use a dowel or a threaded stud with a ground face, keeping the seam out of the loaded zone.
  • Hard chrome and stainless grades are available for wash-down and humid cells.

Applications

Shaft axes suit medium loads over moderate strokes where a sleeve is cheaper than a profile rail. For heavy side loads or a cantilever, compare with the round shaft and profile rail comparison before fixing the layout.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

Most adjustable and closed sleeves are specified against an h6 or g6 shaft. The choice follows the clearance class you want: g6 leaves a little more room and suits a free-running axis, h6 is tighter and suits a preloaded or precision axis. State the bearing part number when ordering Linear Shafts and the shaft tolerance is matched to it.

Case depth follows the diameter: 0.4–0.7 mm below 6 mm, 0.6–1.5 mm from 10 to 15 mm, 0.8–2.0 mm from 16 to 25 mm, and 0.8–3.0 mm above 30 mm. Hardness is HRC 60–62 through the case, with a soft core so the ends can be threaded without cracking.

A single ground shaft is available to 6000 mm. Beyond that, lengths are supplied as a butted joint with a dowel or threaded stud, with the joint face ground so it does not stand proud of the running surface. The joint should sit outside the loaded zone wherever the stroke allows.

Yes. Ends can be threaded, stepped, keyed, drilled or tapped, machined after hardening and before final grinding so the thread stays concentric with the running surface. Hard chrome is available for wash-down and humid service, and stainless grades are available on request.

Support spacing sets the deflection: a long unsupported span sags under the carriage load and the sleeve tightens mid-stroke. The shaft selection guide on this site gives the moment of inertia and the deflection formula, or send the load, span and diameter and our engineers will return the support layout.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Linear Shafts from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts