KH Miniature Linear Bearing: Short Body, 8 mm Bore Up

KH Miniature Linear Bearing: Short Body, 8 mm Bore Up
+

Key Features

Short body for compact heads, with sealed ends and a steel cage that holds the circuits square.

8 mmMinimum bore
ShortBody
UUSeals

Applications

Dispenser heads Lab instruments Small gantries Camera sliders Optical benches

Linear Bearings · KH Miniature Linear Bearing: Short Body, 8 mm Bore Up

Technical Description and Selection Reference

Product Overview

The KH series is the short-body miniature linear bearing. At the same bore as a standard sleeve, the KH body is shorter, which lets a compact head sit closer to the work and keeps the moving mass down. It is the bearing for small gantries, dispenser heads and lab instruments where every millimetre of height counts.

The trade-off is moment capacity: a short body spreads the load over less shaft, so the axis has to be stiff and the load centred. Where the head sees an offset load, a standard body or a longer carriage is the safer choice.

Bores cover the small metric steps with sealed ends and a steel cage. Shaft tolerance stays h6 or g6, housing H7. The bearing guide covers the clearance classes, and the miniature guideway guide compares a shaft axis with a profile rail at the same scale.

ParameterSpecification
SeriesKH miniature linear bearing, short body
Bore rangeSmall metric steps, 8 mm upward
BodyShort, sealed both ends
Ball cageSteel cage
Shaft toleranceh6 or g6
Housing boreH7
SealsUU
Load directionRadial; moment limited by body length
LubricationGrease pre-filled
Operating temperatureConfirmed at quotation for the seal compound
Minimum order1 piece
Lead time3–7 days for stock bores

Product Features

  • Short body lowers the head and cuts moving mass on a small axis.
  • Sealed ends keep fine dust out of a bearing that runs close to the work.
  • Steel cage holds the circuits square at small bores.
  • Fits the same h6/g6 shaft as a standard sleeve, so the shaft is not special.
  • Clearance class quoted per size, so a tight or free feel is chosen, not guessed.

Applications

Small stroke, light load, tight height: the KH body fits where a standard sleeve will not.

About MS Linear

MS Linear is a Chinese manufacturer of precision motion components: profile guideways, ball screws, ball splines, linear shafts, cylindrical guides, linear bearings and single-axis modules. Parts are built to drawing, inspected before shipment, and shipped worldwide.

Read before you specify

Frequently Asked Questions

SDM is the Asian-standard sleeve, LM the metric series and LME the European series. At the same bore, the European body is often longer, which spreads the load and lowers contact pressure. The series is chosen from the drawing and the housing length, not from the bore alone.

The closed type has a fixed clearance class; the AJ adjustable type has a split housing that is tightened until the play is gone. Adjust with the shaft in place, move the carriage over the full stroke, and stop at the point where it still glides without drag. A preloaded sleeve runs hotter and shorter-lived, so do not over-tighten.

Shaft h6 or g6, housing bore H7 for the closed type. The bore tolerance of the bearing is quoted per size, and the fit is what decides whether the axis feels tight or loose. Send the shaft drawing with the order and the pair is checked before shipment.

Yes, an open block carries less moment than a closed block of the same size because the race is interrupted. It is used where the shaft must pass a support rail, and the support spacing, not the bearing, then sets the accuracy.

Sleeves are grease-filled at assembly. Refill at the interval in the lubrication guide, which depends on speed and duty: a slow axis can run for months, while a fast axis needs a shorter interval. Oil is used above the grease speed limit.

Still have questions? Contact our sales team →
China Factory Direct · Drop-in Compatible Dimensions

Buying Linear Bearings from China
is Your Best Choice!

Factory-direct quality and worldwide shipping — standard parts leave the factory in 3–10 days, custom strokes and leads in 15–20 days (2–3 weeks). Send your drawing or the original part number and get a quotation within 24 hours.

Drop-in Replacement Factory-Direct Price Global Shipping OEM / Non-Standard Bulk Discounts